WARNING: To prevent injury always stop the engine or motor before doing any maintenance or repairs to this machine. Separate the connectors between the machine and batteries. Disconnect the wire from the spark plug. How To Check the Engine 1. Check oil level regularly. Change oil after using first two tanks of gasoline. change oil regularly after each twenty- five (25) operating hours, or more often in extremely dirty conditions. 2. Keep the engine clean and remove dirt and oil from coiling fins

8 4 725197 Label, Clarke 1 5 793921 Handle, Hopper 1 6 798203 Spacer, Carrying Handle 2 7 962568 Screw, 5/16 -18 x . Bdg. Hd. 2 8 797820 Shield, Hopper 1 9 962385 Screw, 10-24 x . Bdg. Hd. 3 10 962677 Screw, 10-24 x . Pan Hd. 8 11 791220 Bumper, Front 1 12 962803 Screw 5/16 -18 x 1. 1 13 889706 Wheel, Swivel 2 14 920196 Nut .-13 ESNA 2 15 790823 Bracket, Skirt to Hopper 1 16 798523 Skirt, Hopper 1 17 797220 Retainer, Lower Skirt 1 18 793426 Gasket, Hopper 1 19 797222 Retainer, Hopper Skirt 1 20

5. Check the condition of the batteries. a. Specific gravity (1.280 is ideal for fully charged batteries. b. The battery bank voltage should come up to about 30.7 volts at the end of the cycle. c. The DC charging current should start in the "normal" range and end in the "finish" range. If the charger is still inoperative after the above checks have been made, call your nearest authorized service center. Fig. 12 Page 14 CLARKE TECHNOLOGY Model SPS-28 Space Sweeper Operator's Manual Capacitor Test

Only 1 51 34267A Gasket - Muffler Mtg. (Honda Only) 1 52 215104 Label - Warning 1 53 215106 Label - Warning 1 55 62812A Extension Assembly Honda 1 57 755721 Nipple - 1/4-18 Short 1 58 822806 Elbow - 90° Street 1 59 170266 Coupling - 1/4 NPT 1 60 ref. Drain Plug (part of engine) 1 61 85702A Screw - 1/4-20 x 1 5/8 Hex St. Cap 2 62 85701A Screw - 1/4-20 x 1 1/2 Hex St. Mach 2 63 764541 Hook - Bag Right 1 64 766740 Pin - Locking 2 65 920284 Nut - 1/4-20 Stop 4 66 763740 Grip - Handle 2

Hd. 10 21 962109 Screw #10-24 x 5/8 22 762045 Clamp - R.H. Shield 1 23 762046 Clamp - L.H. Shield 1 24 767841 Shield 25 768543 Scraper - L.H. 1 26 762044 Clamp - Rear L.H. 1 27 930086 Rivet - 3/16 x .450 28 682006 Lid Clamp Assembly 29 763444 Gasket - Intake Hsg. Flange 1 30 66909A Retainer Assembly 1 31 66908A Retainer Assembly 1 32 66907A Retainer Assembly 1 33 763443 Gasket - Impeller Housing 1 34 930113 Rivet - Pop 1/8 35 962241 Screw - #10-24 x 1/2 36 962747 Screw - 3/

x 1. Roll 3 87 790923 Brush Segment Carpet 10 790920 Brush Segment 28" 5 88 797828 Shield Assembly, Broom Dust L.H. 1 89 797223 Retainer, R.H. Skirt 1 90 856702 Pin, Hair, cotter 1 91 797235 Retainer, Brush Strp. (Std Mach. Only) 15 92 980675 Washer, #10 Shakeproof 1 93 798541 Strap, Static Discharge 1 94 798232 Spacer 2 95 797236 Retainer 2 96 858207 Spacer 2 CLARKE TECHNOLOGY Model SPS-28 Space Sweeper Operator's Manual Page 17 CLARKE TECHNOLOGY Model SPS-28 Engine, Dust Control & Handle Assem

You must have training in the operation of this machine before using it. If your operator(s) cannot read English, have this manual explained fully before attempting to operate this machine. Si Ud. o sus operadores no pueden leer el Ingles, se hagan explicar este manual completamente antes de tratar el manejo o servicio de esta maquina. All directions given in this book are as seen from the operator’s position at the rear of the machine. For new books write to: Clarke® , 2100 Highway 265, Springd

The carbon brushes in the motor must be checked every three months, or every 500 hours ofoperation, whichever comes first. If either of the brushes is shorter than 3/8 inch, replace both of the carbonbrushes. How To Check The Commutator And The Carbon Brushes WARNING: Electrical inspections must be madeby a person authorized to makeelectrical repairs. To check the commutator and the carbon brushes follow this procedure: 1. Disconnect the power cord from the electrical outlet. 2. Empty both tanks

Description Qty 1 59721A Valve-Drain 1 1A 53606A Elbow-45 Degree, Drain 1 2 962929 Screw, 10-32 x 3/8 1 3 52636A Latch, Tank 2 4 837304 O-Ring (Small) 1 4A 4B 920797 Nut Drain Valve Lock 2 5 30322A Tank, Recovery 1 *6 690212 Adaptor Asm.-Vac Hose 1 *7 692701 Elbow - 90 Degree 1 8 55674A Lid 6" Clear 1 8A 34288A Gasket** 1 8B 692409 Chain-Cover 1 9 85613A Screw, 8-32 x 7/8 Pan Hd 1 9A 81109A Nut, Hex Elastic Lock 1 10 52806A Vac Manifold Asm. (incl. 10, 10A, 1 11, 12, 13) 11 920797 Nut Drain Valv

When used with a floor tool, the machine applies cleaning solution to the carpet and removes the dirty solution and soil from the carpet. • The extractor has controls to start the pump for the solution and the motor for the vacuum. The floor tools have controls to release the solution. • The extractor has a bypass pump. The pump runs when switched on, bypassing solution internally to keep pressure even.The extractor starts when the solution lever on the floor tool is activated. SPECIFICATIONS Be