Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
ASSY. ( INCL. 17, 37, 38, 45 ) 900749 1 900749 1 900749 1 34 WHEEL ASS’Y (INCLUDE 21) 900509 4 900509 4 900509 4 35 WASHER 0.75 “C” 900997 0-1 900997 0-1 900997 0-1 36 37 SCREW CAP 5/16-18 X 1” *8041028 2 *8041028 2 *8041028 2 38 SPACER 0.340” I. D. X 0.330” LG. 900745 2 900745 2 900745 2 39 PLATE - BRACE REAR 900905 2 900905 2 900905 2 40 SCREW CAP 1/4-20 X 1/2 *8041002 4 *8041002 4 *8041002 4 41 SPACER 900926 6 900926 6 900926 6 42 SCREW, SELF TAPPING 10 - 24 NC X 1/2 LG. *8123086 1 *8123086 1 *8123086 1 43 NOZZLE MAIN FRAM. ASS’Y - GREEN (INCL. item (qty) 44 (1), 42 ( 1) , 55( 1), 64(1), 70(1)) 900931 1 900931 1 900931 1 44 PLUG 900146 1 900146 1 900146 1 45 PLATE QUAD ADJUSTABLE 900746 1 900746 1 900746 1 46 GASKET - - 800411 1 800411 1 47 IMPELLER ASS’Y’ (INCLUDES iTEM 49, 50, 51) 900003 - S 1 900215 -S 1 900215 - S 1 48 HEIGHT ADJUST ASSY 890326 1 890326 1 890236 1 49 KEY HI PRO 5/32 X 5/8 900162 2 900162 1 900162 1 50 WASHER LOCK 3/8 TWISTED TOOTH 400502 1 400502 1 400502 1 51 SCREW CAP 3/8-24 x 1" TORQUE 50 FT- LBS (68 N.m) 900154 1 900154 1 900154 1 52 HOUSING ASS’Y (INCL. 1 EA . ITEMS 13, 65, 67, 68, 69, 70) 900757 1 900757 1 900757 1 53 ENGINE 5.5 HP HONDA 900615 1 - - - - ENGINE 5 HP BRIGGS & STRATTON "IC" QUANTUM - - 900273 1 - - ENGINE 5 HP BRIGGS & STRATTON QUANTUM - - - - 900622 1 54 NUT LOCK 5/16 - 18 HEX *8160002 1 *8160002 3 *8160002 3 55 ROD - BUMPER 900939 1 900939 1 900939 1 56 SCREW CAP 5/16 - 18 x 1 - 1/4 LONG - - *8041029 2 *8041029 2 SCREW CAP 5/16 - 18 x 1 - 1/2 LG. *8041030 1 - - - - 57 CAP - HUB 900486 4 900486 8 900486 8 58 WASHER - FLAT 1/2 “SAE” *8172011 8 8172011 8 *8172011 8 59 PLATE BRACE HT. ADJ. KD / TKD 900756 1 900756 1 900756 1 60 61 PIN - COTTER 3/32 X 3/4 *8197016 4 *8197016 4 *8197016 4 62 LABEL DANGER FLYING MATERIAL 810736 1 810736 1 810736 1 63 LABEL DO NOT FILL WHEN ENGINE IS HOT 400268 1 400268 1 400268 1 64 GUARD FOAM INSERT 900977 1 900977 1 900977 1 65 DOOR EXHAUST ASSY (incl. items 62) 890148 1 890148 1 890148 1 66 67 SCREW CAP # 10-24 *8059135 2 *8059135 2 *8059135 2 68 NUT LOCK # 10-24 *8164005 2 *8164005 2 *8164005 2 69 WASHER # 10-24 *8171001 2 *8171001 2 *8171001 2 70 LABEL DANGER KEEP HANDS and FEET 400424 2 400424 2 400424 2 71 LABEL READ OWNER'S MANUAL 890301 1 890301 1 890301 1 * Denotes standard hardware that may be purchased locally. Part No. 890310 P a g e 7 of 8 Form No. F010396B IMPELLER REMOVAL continued A A A Use only a qualified mechanic for any adjustments, disassembly or any kind of repair . WARNING: TO AVOID PERSONAL INJURY, ALWAYS TURN MACHINE OFF, MAKE SURE ALL MOVING PARTS COME TO A COMPLETE STOP. DISCONNECT SPARK PLUG WIRE BEFORE SERVICING UNIT. ENGINE: See engine manufacturer ^|r operator's instructions. DEBRIS BAG: See page 5. RECONNECT SPARK PLUG WIRE, GUARDS, BAG, CAPS AND / OR HOSE BEFORE STARTING ENGINE. 17.2 IMPELLER REMOVAL I.Wait for engine to cool and disconnect spark plug. 2 .Drain fuel and oil from the engine. 3.Remove bag, quick release, and upper handle. Do not kink, stretch, or break control cables, control housings, or end fittings while removing handles. 4.Invert and support machine with engine not touching ground to prevent damage to recoil starter. 5.Disassemble housing by removing six (6) lock nuts and washers from nozzle frame, (2 are inside of nozzle opening). 6.Remove impeller bolt and lock washer. 7.Lift impeller upward. If impeller slides freely, proceed to (step 10). 8 .Place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck impeller. 9.If the impeller does not loosen, obtain a 1” (25.4mm) longer bolt of the same diameter and thread type as the impeller bolt. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or wheel puller against the bolt head and the impeller back-plate (near the blades), remove impeller from shaft. 10.Remove engine mounting screws, bolts, and nuts as required. 11.When impeller is free of the engine shaft, lift impeller and housing assembly off engine. Align impeller with opening, and diagonally lift impeller out of housing. 12. Using a new impeller bolt and lockwasher, reinstall new impeller in reverse order. 13. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs.(68 N.m) (see item 51 on page 7). 14. Reinstall engine onto housing in reverse order of removal. 15. Invert machine back onto all 4 wheels. 16. Reinstall spark plug wire. Maintenance Schedule ;ollow these hourly maintenance intervals. Maintenance Operation Every Use Every 5 hrs or (Daily) Engine (See Engine Manual) Check for excessive vibration • Clean Debris Bag • Check bag strap tightness • Inspect for loose parts • Inspect for worn or damaged parts • 20 TROUBLESHOOTING Before Requesting Service Review These Suggestions Problem Possible Cause Solution Wil...
Эта инструкция также подходит к моделям:Пылесосы - KD505H (239.93 kb)
Пылесосы - KD505Q (239.93 kb)