Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Do not kink, stretch, or break control cables, control housings, or end fittings while removing handles. 4.Invert and support machine with engine not touching ground to prevent damage to recoil starter. 5.Disassemble housing by removing six (6) lock nuts and washers from nozzle frame, (2 are inside of nozzle opening). 6.Remove impeller bolt and lock washer. 7.Lift impeller upward. If impeller slides freely, proceed to (step 10). 8 .Place two crowbars between impeller and housing on opposite sides. Pry impeller away from engine until it loosens. Using a penetrating oil can help loosen a stuck impeller. 9.If the impeller does not loosen, obtain a 1” (25.4mm) longer bolt of the same diameter and thread type as the impeller bolt. Thread longer bolt by hand into the crankshaft until bolt bottoms. Using a suitable gear or wheel puller against the bolt head and the impeller back-plate (near the blades), remove impeller from shaft. 10.Remove engine mounting screws, bolts, and nuts as required. 11.When impeller is free of the engine shaft, lift impeller and housing assembly off engine. Align impeller with opening, and diagonally lift impeller out of housing. 12. Using a new impeller bolt and lockwasher, reinstall new impeller in reverse order. 13. Tighten impeller bolt. Torque impeller bolt to 50 Ft. Lbs.(68 N.m) (see item 51 on page 7). 14. Reinstall engine onto housing in reverse order of removal. 15. Invert machine back onto all 4 wheels. 16. Reinstall spark plug wire. Maintenance Schedule ;ollow these hourly maintenance intervals. Maintenance Operation Every Use Every 5 hrs or (Daily) Engine (See Engine Manual) Check for excessive vibration • Clean Debris Bag • Check bag strap tightness • Inspect for loose parts • Inspect for worn or damaged parts • 20 TROUBLESHOOTING Before Requesting Service Review These Suggestions Problem Possible Cause Solution Will not vacuum or has poor vacuum performance. Dirty debris bag. Nozzle height set too high or too low. Hose kit cap missing. Clogged nozzle or exhaust. Excessive quantity of debris. Clean debris bag. Shake bag clean or wash. Adjust nozzle height. Check for hose kit cap. Unclog nozzle or exhaust (see page 5). Allow air to feed with debris. Abnormal vibration. Loose or out of balance impeller or loose engine. Check impeller and replace if required. Check Engine. Engine will not start. Stop switch off (Honda only). Throttle in off position. Engine not in full choke position (Honda only). Out of gasoline. Bad or old gasoline. Spark Plug wire disconnected. Dirty air cleaner. Check stop switches, throttle, choke position and gasoline. Connect spark plug wire. Clean or replace air cleaner. Or contact a qualified service person. Engine is locked, will not pull over. Debris locked in impeller. Engine problem. See page 5, Contact an engine servicing dealer for engine problems. Nozzle scrapes ground in lowest height setting. Nozzle height out of adjustment. Adjust nozzle height. (See Nozzle height fine adjustment for hard surface use on page 5). Engine Service and Warranty Contact your nearest engine manufacturer's authorized servicing dealer. 21 Serial Plate Record your machine model, serial number and date-of-purchase and where purchased 96 1803 S. Jefferson P.O. Box 308 Lee's Summit, MO 64063 / USA Tel (816) 524-9666 Fax (816) 524-6983 Operator Purchase Date_ Purchased from- 22 WARRANTY PROCEDURE Please fill in the WARRANTY CARD and send the upper part to Billy Goat. The WARRANTY terms are stated on the lower part which remains with the user. Whenever a Billy Goat Machine is faulty due to a defect in material and / or workmanship, the owner should make a warranty claim as follows: The Machine should be taken to the dealer from whom it was purchased or to an authorized Billy Goat dealer. The owner should present the remaining half of the Warranty Registration Card, or, if this is not available, the invoice or receipt. The Warranty Claim will be filled in by the authorized Billy Goat Dealer, who will send it with the faulty part to Billy Goat headquarters. The Quality / Service department at Billy Goat headquarters will study the claim and parts and will notify their conclusions. The decision by the Quality / Service department at Billy Goat headquarters to approve or reject a Warranty claim is final and binding. Note: To process a Warranty Claim, it is necessary to quote the Model & Serial number who are printed on the Billy Goat Serial Plate. BiLLV GOAT INDUSTWESINC BILLY GOAT INDUSTRIES INC. PO. BOX 308 1803 S JEFFERSON LEE'S SUMMIT, MO 64063 / USA PHONE: 816-524-9666 FAX: 816-524-6983 Part No. 890310 P a g e 8 o f 8 Form No. F010396B...
Эта инструкция также подходит к моделям:Пылесосы - KD505ICQ (239.93 kb)
Пылесосы - KD505Q (239.93 kb)