Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
1 Section Three - AT Command Set ............... 6 Section Four - S Registers ........................ 13 Section Five - Result Codes ...................... 14 Section Six - Troubleshooting.................... 15 Section Seven - Support and Service......... 17 Appendix A - Specifications ..................... 17 Appendix B - Notices ................................ 17 Part #MAN152 Rev. 1.0 V.90-CL The information contained in this manual has been validated at the time of this manual's production. The manufacturer reserves the right to make any changes and improvements in the product described in this manual at any time and without notice. Consequently the manufacturer assumes no liability for damages incurred directly or indirectly from errors, omissions or discrepancies between the product and the manual. All registered trademarks are the property of their respective owners. Copyright © 1997 All rights reserved. No reproduction of this document in any form is permitted without prior written authorization from the Manufacturer. Section One - Introduction The MaxTech XPVS56P/C PCI Plug and Play Data, Fax, Voice Speakerphone Modem connects your computer to all popular high speed modems available today. The modem utilizesV.90 (56Kbps)technology to provide increased download speeds using regular telephone lines. The modem incorporates Plug and Play for ease of installation. This manual describes the hardware installation procedures for your new modem. Additional information on AT commands and S-registers is provided so that your system can be customized for a particular operating environment. *Note: V.90 is capable of downloading at 56Kbps. However, current FCC regulations limit its speeds to 53Kbps. Section Two - Installation This section will provide step by step instructions on how to install your new 56 Kbps Data, Fax, Voice, Speakerphone modem. Installation of this modem is a two- step process consisting of: 1) hardware installation and 2) communication software installation. 2.1 Unpacking Your Modem Be certain that you have all the items listed below. This package contains: • A modem • A telephone cable • User's manual • Software for the modem • Software user's manual 2.2 What You Need You will need: 1. A phillips-head screw driver. 2. A computer running Microsoft Windows 95 or later. 3. An available PCI slot in your PC. Proceed to Section 2.3 now if you have everything required. 1 2.3 Hardware Installation Installation of this modem requires opening and manipulating your PC. Exercise caution at all times when working with AC powered and static-sensitive equipment. Turn off and unplug your PC before installation. Discharge any static electricity from your body by touching any grounded metal surface of the PC system, such as its power supply cover. 1. Turn off and unplug your computer from the AC outlet. 2. Remove your computer's cover (refer to your computer's owner's manual). 3. Select any available 32-bit PCI card slot and remove the slot cover (refer to Figure 2-3). Figure 2-3 PCI Expansion Slots 4. Carefully slide the PCI internal modem into the slot you have chosen, applying even pressure until the modem is completely seated in the slot. 5. Fasten the retaining bracket with the screw from the slot cover. Make sure the modem is properly aligned. Store the slot cover for future use. 6. Replace the computer cover and plug in your computer. 7. Connect the telephone cable from the modem's LINE connector to the telephone wall jack. 8. Optionally, connect your telephone to the modem's PHONE connector, a microphone to the MIC connector and a speaker to the SPK connector. 9. Turn your computer on. Your modem is now installed. 2 2.4 Hardware Configuration The version of Windows 9x you have will determine which set of dialog boxes is presented to you when installing the modem in Windows 9x. Proceed to one of the following sections, depending on your Windows 9x's diaglog box: • Section 2.4.1 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the New Hardware Found dialog box • Section 2.4.1.1 when Windows 95 starts for the first time after card installation, it detects the modem and it displays the Update Device Driver Wizard. • Section 2.4.1.2 When Windows 98 starts for the first time after card installation, it detects the adapter and displays the Add New Hardware Wizard. 2.4.1 Windows 95 Release 4.00.950 When Windows 95 starts for the first time after card installation, it detects the modem and displays the New Hardware Found dialog box. Under New Hardware Found, when asked to “Select which driver you want to install for your new hardware,” click on “Driver from disk provided by hardware manufacturer.” Click “OK.” The Install From Disk dialog box now instructs you to “Insert the manufacturer's installation disk into the drive selected, and then click OK.” Insert the modem's driver diskette into the disk drive and type A:\ (or B:\ if inserted in drive B) in ...