Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Take care not to bump yourself or others with it. • When placing the projector in the carrying bag, remove the connection cables. Otherwise, damage to the connectors and cables may result. Status before preparation (When stored) 1) Set up arm. 2) Rotate arm. 3) Raise camera head. Using the camera removed from the projector 2 1 1 PRECAUTIONS • Installation of the document camera onto the tray should be performed in the reverse order shown above. • When replacing the document camera on the tray, ensure that the lock lever is securely locked in position. • When using the tip resistant bars, pull them fully until each forms the angle of 90 degree. If you don’t use the bars, the camera may topple over. Status before preparation (When stored) 1) Disconnect the RGB cable, then slide the lock switch to release lock. 2) While pushing the lock lever in the arrow direction, lift up the document camera. 4) Extend the tip resistant bars to set the document camera. 5) Connect the document camera and the projector using the supplied RGB cable. 3) Remove the document camera from the tray. Pull up toward direction q Operations ¦ Image projection 1 Place the document. Set the document at the 2 Press the CAMERA button, and select camera • The input returns to the previous input when the CAMERA button is pressed again. • Camera input can also be selected by pressing either the INPUT button. 3 Rotate the camera head to align the orientation of the document shooting by checking the screen. 4 Move the camera arm up and down to adjust the image size. Farther ( ^ ): Smaller image Closer ( v ): Larger image • Closeup shot with the distance shorter than 100 mm cannot be performed. 5 Adjust the focus using the focusing lever on the camera head Focusing lever Rotate the focusing lever to either NEAR or FAR, whichever is better in focusing. • Near : 100 mm to 300 mm Far : 300 mm to 5 m 36 6 If the screen buttons to make The Sharpness of the the Image adjustment menu p.30 . 7 After use, fold up the document 1 Lay down a piece of white paper, and adjust so it fills the screen. Although the projector’s camera is constantly adjusting the color balance of the images it photographs, the color balance may be disrupted, depending on the the document. If this happens, the white balance can be locked using the below. • If the room’s fluorescent lighting causes the image to flicker, either turn off the fluorescent light, or set the Shutter from the Image adjustment menu p.30 . Note that changing the Shutter setting may not eliminate the flicker, depending on the lighting, state of the document, or image adjustment. Fold up the camera using the reverse p.34 . Notes • There is no audio output when camera input ¦ Locking the white balance Adjust the camera head and arm so that the white paper fills the screen completely. 2 Set the White balance to Lock in the Image adjustment menu. p.30 The white balance is locked. If you want to return to the auto adjustment, set the White balance to Auto in the Image adjustment menu. Notes • If the white balance is set to Lock, once power is turned off, the setting goes back to Auto. • The color of the room lighting may prevent the white balance from being adjusted to the optimum level. In this situation, or if you want to use a certain tinting, adjust the R-level, G-level and B-level on the Image adjustment menu p.30 . 37 About lamp The product’s light source is lamp that lights pressure. Be sure to fully understand characteristics of the lamp care. • The lamp may explode with a loud noise or fail to light at the expiration of its life. •How long it takes before the lamp explodes or the life expires may vary greatly by lamp. Some may explode shortly after first use. (Free replacement is available if the lamp explodes within the warranty period. Contact the dealer from whom purchased the product in such a case.) • Explosion is likely to happen if the lamp is used after has elapsed. • When the lamp explodes, the broken pieces of glass may get inside the product or be released outside from the openings for ventilation. • When the lamp explodes, a slight amount of mercury gas enclosed in the lamp along with glass dust may be released from the openings for ventilation. ¦ Immediately replace the lamp when a sign • When the replacement time approaches, a message will appear on the screen. • The risk of explosion will increase if the lamp is continuously used without being replaced. •Frequently check the used hours and prepare spares when the replacement time approaches. (Refer to “Status display”. p.33 ) ¦ When the lamp is broken • If glass components, including a lamp and a lens, should break, handle the broken pieces with care to avoid injury and contact your dealer for repair service. • In the event of lamp explosion, unplug the product from the wall outlet, leave and completely ventilate the room. Then, thoroughly clean the area around the projector and discard any edible items placed in that area. • When the lamp ex...
Эта инструкция также подходит к моделям:Проекторы - TDP-S20U (5.57 mb)