Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
(7) Remove TV stand support frame. (8) Remove the EMI Aluminum Foil Sheilding Tape from the LCD Panel (PIC1, 2) (9) EMI Aluminum Foil Sheilding Tape must be replaced during assembly. Remove the EMI Aluminum Foil Shielding Tape which secures the Keyboard wiring to the panel. (10) Remove from the D-sub board Speaker wire, Front/Side Control Button wire, and A/V wire connectors (PIC1) (11) Remove the black tape from the Speaker wire and Ceramic ring (PIC2) (12) Replace black tape during assembly. (13) Remove the foam spacer from LCD Panel and remove the A/V wire under the frame (PIC1). (14) Save foam spacer and place in position during assembly. (15) Remove the A/V subassembly from the bezel (PIC2). (16) Remove screws (PIC1) in the sequence: 1-2 (17) Disconnect the LCD Panel cable from the D-SUB board (PIC1) (18) Remove screws that secure the LCD panel to the bezel (PIC1, PIC2) (19) TWO MEN REQUIRED!! Lift LCD Panel from the bezel (20) Replace LCD panel. (21) The front bezel can now be replaced if needed. Note: Before returning this product to the end user, you must follow the steps outlined in the section, Before Returning This Product to the User, on page 19. This procedure ensures that the chassis will not cause electric shock. A/V Board Removal and Replacement Note: Before disassembly of any part the TV, make sure the power is OFF, and the power cord is removed from the wall outlet. Allow time for power within all system boards to discharge before you begin disassembly. Never insert any objects into the vent holes in the TV case. (1) Disassemble control box cover and rear cabinet cover and remove A/V assembly. (2) Using a small pair of wire cutters grip the side-locking tab and pivot back towards the A/V cable connector (PIC1). Locking tabl should only pivot about 45 degrees. Do the same for the opposite side of the A/V assembly. (3) Slide out A/V board and replace (PIC2). (4) Push locking tabs in to secure replaced A/V board. PIC1 PIC2 Note: Before returning this product to the end user, you must follow the steps outlined in the section, Before Returning This Product to the User, on page 19. This procedure ensures that the chassis will not cause electric shock. IR Board Removal and Replacement Note: Before disassembly of any part the TV, make sure the power is OFF, and the power cord is removed from the wall outlet. Allow time for power within all system boards to discharge before you begin disassembly. Never insert any objects into the vent holes in the TV case. (1) Disassemble rear control box cover and rear cabinet cover. (2) 2. Remove screws 1 and 2 and replace IR board (PIC1). PIC1 Note: Before returning this product to the end user, you must follow the steps outlined in the section, Before Returning This Product to the User, on page 19. This procedure ensures that the chassis will not cause electric shock. 1 2 PIC1 Front/Side Control Buttons Removal and Replacement Note: Before disassembly of any part the TV, make sure the power is OFF, and the power cord is removed from the wall outlet. Allow time for power within all system boards to discharge before you begin disassembly. Never insert any objects into the vent holes in the TV case. (1) Disassemble control box cover and rear cabinet cover. (2) The control button board is attached with glue. Use alcohol to soften the glue and remove the control button board (PIC1...
Эта инструкция также подходит к моделям:Принтеры - FLM-2632 (2.56 mb)
Принтеры - FLM-2632M (2.56 mb)
Принтеры - FLM-2634B (2.56 mb)
Принтеры - FLM-3232 (2.56 mb)