(277 kg)/ 40 lb./sq.ft. (196 kg/sq.m) 110 lb. (50 kg.) 60 gal. (227 l.) 55 gal. (208 l.) 2806 Heritage Oval 6' x 36" L 72" (1829mm) W 35-3/4" (908mm) H 21-1/2" (546mm) A 17" (432mm) B 11" (279mm) C 19-1/2" (495mm) Template Provided As Desired 5-1/2" (140mm) 744 lb. (338 kg)/ 41 lb./sq.ft. (200 kg/sq.m) 135 lb. (61 kg.) 73 gal. (276 l.) 44 gal. (166 l.) 2903 Savona Oval 5' x 42" L 60" (1524mm) W 42-1/4" (1073mm) H 21-1/4" (540mm) A 17" (432mm) B 9-1/2" (241mm) C 19-1/4" (489mm) Template Provided

A31 ELECTRICAL INSTALLATION INSTRUCTIONS (continued) ELECTRONIC ACTIVATED COMBINATION TUB WITH LIGHTS (4 BUTTON PANEL) 120V, 60HZ 15A GFCI (FOR HEATER) ELECTRICAL FEED GFCI 120V, 60HZ 15A GFCI ELECTRICAL FEED GFCI 120V, 60HZ 15A GFCI ELECTRICAL FEED GFCI ELECTRICAL INSTALLATION INSTRUCTIONS (continued) USE THREE JUNCTION BOXES (CANADA MARKET) ECOSILENT PUMP HAS P3JJ PLUG WHIRLPOOL HEATER IS FACTORY INSTALLED ON COMBINATION TUBS Green/Copper Black White Green/Copper Black White Green/Copper Black

(311 kg)/ 95 lb. 71 gal. 64 gal. StudioW 36" (914mm) (451mm) (470mm) (1486mm) (1529mm) 46 lb./sq.ft. (209 kg.) (269 l.) (243 l.) 5' x 36" H 22-1/2" (572mm) B 11" x 34-1/2" x 34-1/2" (223 kg/sq.m) (279mm) (876mm) (876mm) 2935 N/A L 60" (1524mm) A 17-3/4" C 20-1/2" N/A 60-3/16" 686 lb. (311 kg)/ 95 lb. 71 gal. 64 gal. StudioW 35-7/8" (911mm) (451mm) (521mm) (1529mm) 46 lb./sq.ft. (209 kg.) (269 l.) (243 l.) 5' x 36" H 22-1/2" (572mm) B 11" x 34-3/8" (223 kg/sq.m) w/Tile Flange (279mm) (873mm) TABL

Attach the 8 AWG solid copper conductor supplied with the heater from the heater bonding lug to the motor frame bonding lug as shown in Figure 3. The conductor is secured to the lugs using set screws. The motor frame shall have a second 8 AWG solid copper conductor connected from the frame bonding lug to the home’s electrical panel or approved local bonding point as shown in Figure 3. NOTE: For all “EcoSilent” pump configurations, the pump housing is plastic. Therefore, the first copper conducto

TO CONTROL PANEL TO BLOWER 3. 754025-0073A CABLE EXISTING (INCLUDES ADAPTER CABLE BOX SHOWN) REMOTE BLOWER LOCATION OPTION (continued) FOR THE COMBINATION WHIRLPOOL / AIR BATH CONFIGURATIONS ONLY: Up to two additional control box extensions (P/N 754512-0070A) are required as shown in photo 4 (below). Simply extend the cables going to the blower by adding in the extension cables. Be careful not to damage the cable connections and never plug in cables while power is applied to blower and/or pump.

The cycle will start on white. • Turn off and on within 3 seconds; it will change to slow rainbow cycle and so on per the display color table shown above. 754532-100 Rev. A 40 Operation: Combination Tub with Lights (continued) EXITING THE BATH • Be sure to turn off the air blower before draining bath. • Open drain by rotating drain knob clockwise. DRYING CYCLE OPTIONS STANDARD DRYING CYCLE An automatic drying cycle will start 20 minutes after the blower is turned off. The blower LED blinks while

WARNING: Pregnancy. If you are or think you may be pregnant, consult your physician before using the bathtub. Use this unit only for its intended use as described in this manual. Do not use any attachments not recommended by American Standard. The unit must be connected only to a supply circuit that is properly protected by a ground-fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a routine basis. To test the GFCI, push the test button. Th

OPERATING AIR MASSAGE SYSTEM: ON/OFF: Press this button once to turn air-blower on. Press again to turn air-blower off. AIR SPEED INCREASE: Pressing this button will increase to the next higher speed. AIR SPEED DECREASE: Pressing this button will decrease to the next lower speed. WAVE FUNCTION: Press this button to start the wave function (button will light). Blower speed will continuously vary between high and low. Press again to exit wave function (button light will go out). EXITING THE BATH •

Your new bath is shipped to you after careful inspection. The whirlpool and air bath versions are completely assembled with pump/blower and system piping. All you need to finish the installation are your selected fittings and electrical connections. To ensure maximum performance and pleasure from this product, please follow the instructions and cautions. For questions or service issues, please call Technical Support 1-(800)-442-1902. Please do not contact or return product to the store. © AS Ame

It will only turn the heater off if the thermostat fails. If the high-limit trips frequently, call a service technician. To manually reset the circuit in the event that the “High-Limit” switch has been activated, simply (1) Turn off the whirlpool pump. (2) Drain water from the tub. (3) Remove power from heater by unplugging at receptacle or turning off circuit breaker. (4) The heater circuit will automatically reset in less than 15 minutes. (5) Restore power to the heater. (6) Whirlpool bath is