Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
When Reverse Mode is on with cassettes in both decks A and B After the reverse (2) side of the tape finishes playing, the tape in the other deck starts playing. Locating the Beginning of a Song —Music Scan You can use Music Scan to locate the beginning of a song. Music Scan searches for blank portions that usually separate recorded songs, then plays the next song. To find the beginning of the current song During play, press . or 1 in the opposite direction to the tape play. The tape direction indicator of the opposite direction to the tape play starts flashing slowly. Searching stops automatically at the beginning of the current song, and the current song starts automatically. To find the beginning of the next song During play, press . or 1 in the same direction as the tape play. The tape direction indicator of the same direction as the tape play starts flashing slowly and quickly alternately. Searching stops automatically at the beginning of the next song, and the next song starts automatically. Music Scan works by detecting a 4-second long blank between each song, so it will not work well in the following cases • No blank at the beginning of a song. • Noise (often caused by much use or poor quality dubbing) which fills the blank. • Long, very soft passages or pauses in a song. The use of the C-120 or thinner tape is not recommended, since characteristic deterioration may occur and this tape easily jams in the pinch- rollers and the capstans. – 30 – Using DSP Surround Mode Using DSP Surround Mode In order to reproduce a more acoustic sound field in your listening room while playing any source, you can use following DSP Surround modes. • DSP Surround mode can be also used for a disc encoded with Dolby Digital 5.1ch or with MPEG Multichannel. You can select one of the following DSP Surround modes according to your preference. S (Small) THEATER: Reproduces the sound field of a small theater (where the seating capacity about 300). L (Large) THEATER: Reproduces the sound field of a large theater (where the seating capacity about 1,000). LIVECLUB: Gives the feeling of a live music club with a low ceiling. PAVILION: Gives the spacious feeling of a pavilion with a high ceiling. CHURCH: Gives the spacious feeling of a majestic church with a high ceiling. Activating and Adjusting the DSP Surround Mode You can use the DSP Surround mode for any source you like. On the remote control: Only when using the remote control, you can adjust the delay time of the surround speakers. 1Press DSP SURROUND, while holding down SHIFT, to select a desired DSP Surround mode. + • Each time you press the button, the DSP Surround mode changes as follows: S THEATER L THEATER LIVECLUB PAVILION (DSP off) CHURCH OFF • When one of the DSP Surround modes is activated, the SURROUND lamp on the unit lights up. 2Press LEVEL SELECT repeatedly until “DELAY” appears on the display. 3Press LEVEL + / – to adjust the delay time. • Each time you press the button, the delay time changes as follows: DELAY 1 DELAY 2 DELAY 3 DELAY 4 DELAY 5 DELAY 6 As the number increases, the delay time increases so that you can obtain much larger sound field. • This setting does not affect the delay time setting of the “SPEAKER SETTING.” (See page 40.) To cancel the DSP Surround mode, select “OFF” in step 1 so that the SURROUND lamp goes off. On the unit: When using the buttons on the unit, you can activate the DSP Surround modes, but cannot make delay time adjustment. Press DSP SURROUND > or < to select a desired DSP Surround mode. • Each time you press the button, the DSP Surround mode changes as follows: S THEATER L THEATER LIVECLUB PAVILION (DSP off) CHURCH OFF • When one of the DSP Surround modes is activated, the SURROUND lamp on the unit lights up. To cancel the DSP Surround mode, select “OFF” so that the SURROUND lamp goes off. When you use one of sound modes with surround elements—D.CLUB, HALL, STADIUM (see page 13) You can set these sound modes together with the DSP Surround modes, but the surround elements of these sound modes are changed to the DSP Surround mode. – 31 – Recording Continued IMPORTANT: • It may be unlawful to record or playback copyrighted material without the consent of the copyright owner. • The recording level is automatically set correctly, so it is not affected by the VOLUME, the SUBWOOFER LEVEL, the SOUND MODE, and the DSP Surround controls. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level. • If recordings you have made have excessive noise or static, the unit may be too close to a TV. Increase the distance between the TV and the unit. • You can use type I tape for recording. To protect your recording Cassettes have two small tabs on the top to protect from unexpected erasure or re-recording. To protect your recording, remove these tabs. To re-record on a protected tape, cover the holes with adhesive tape. To keep the best recording and playback sound quality If the heads, ...
Эта инструкция также подходит к моделям:Посудомоечные машины - CA-MXDVA9 (3.4 mb)