Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
If you install your stove in the same room as the Cold Air Return from your home’s Central Furnace, you must place your stove at least 20 feet (20’) from the Cold Air Return. We recommend you open an outside window slightly, and never close the door that leads from this room to the rest of your home. IN THE EVENT OF SMOKE-BACK 1. If you see smoke coming out of your unit into the room due to a power failure, DO NOT OPEN THE HOPPER OR DOOR TO YOUR UNIT!! Remain calm. Open the nearest outside door and windows and wait for all signs of smoke to clear (at least one hour, although the smoke should dissipate quickly once the door and windows are opened). When power is restored, press the ON button to restart your unit, and let the unit run for at least 30 minutes. -- If you see any further signs of smoke-back, press the OFF button and call Technical Support at (800) 245-6489 before restarting your unit, as damage could have occurred due to the power failure. -- If you see no more signs of smoke-back, press the OFF button and wait for your unit to completely shut down and cool down, then clean the burn pot area before restarting your unit (see “Before Re- Starting Your Unit,” above). 2. If you see smoke coming out of your unit into the room and the power has not failed, DO NOT OPEN THE HOPPER OR DOOR TO YOUR UNIT!! Remain calm. Immediately press the OFF button, open the nearest outside door and windows and wait for all signs of smoke to clear (at least one hour, although the smoke should dissipate quickly once the door and windows are opened). Do NOT restart your unit before calling Technical Support at (800) 245-6489. Text Box: Text Box: Please call Technical Support at (800) 245-6489 with any questions. England’s Stove Works, Inc. IMPORTANT INFORMATION 1. Check local installation codes for your area. Call your Homeowner’s Insurance representative for inspection of your stove’s installation. 2. Read and comply with the instructions in this manual. 3. This unit should be tested (dry run) before loading pellets for 20 minutes. The stove should automatically shut itself off after the 20-minute dry run. 4. Your stove is designed to burn Premium Wood Pellets only. Burning pea coal, cherry pits, or anything other than wood pellets will void your warranty. Pellets with high ash content will burn dirty and require the unit to be cleaned more often. This unit is designed for use with .” diameter pellet fuel. Using pellets longer than 2” can bind the auger and require frequent manual removal. 5. Be sure your pellets are not damp or wet. Keep sawdust out of the unit. 6. Use three-inch (3”) U.L.-approved PELLET VENT TWIST-LOCK PIPE when installing this stove and follow the manufacturer’s specifications for installation and clearances (we highly recommend Simpson Dura-Vent pellet twist-lock pipe) (AC-3000 kit). For installations over 4000 ft. above sea level the exhaust should be vented with 4"pellet vent pipe (AC-3100 kit). Even though this pipe interlocks, it is a good idea to seal all connections with high temperature silicone (AC-RTV3). Use at least three screws to secure the pipe to this unit’s exhaust blower. Also, if you do not use U.L.-approved twist-lock pellet pipe, be sure to use U.L.-approved Pellet Vent pipe, and fasten each joint of the pipe with at least three screws. Outside combustion air is mandatory for these units to work properly. Make this connection using a 1 7/8” I.D. metal pipe (steel, aluminum or copper) and coupler. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end should be covered (screened) to prevent any foreign matter from entering the system. Try to keep the number of bends in this pipe to a minimum. Our Part Number PU-OAK (Outside Air Kit with flex pipe) can be used. NOTE: If an older unit, measure the opening to determine what size pipe to use. NOTE: If the total run of the intake air connection exceeds 6’, use 3” metal pipe and coupler instead. 7. Regularly inspect the burn pot area and, if any crust forms, remove it with a poker. 8. The ash in the burn pot should be removed regularly, depending on your burn rate. The area to the right and left of the burn pot is for ash storage; keep the air holes in the burn pot clean for a more efficient burn. Check your exhaust system frequently. Refer to “Ash Removal and Disposal” section. 9. Keep pellets and all other combustible materials a safe distance from the unit. 10. This unit will require floor protection if installed on a combustible surface. The minimum floor protector for this unit is 36” x 36” which should give you at least six inches (6”) of protection at the rear and each side, and six inches (6”) minimum in the front of the unit. 11. Horizontal runs should not exceed four feet (4’) with a maximum vertical flue height of thirty five feet (35’). At fifteen feet (15’), the pipe should be increased to four inch (4”) pellet vent pipe. 12. This unit should be turned off and allowed to cool prior to cleaning....