Оценок - 1, средний балл: 5
(
)
)
|
Фрагмент инструкции
The following Parts Identification Listing and the step by step assembly procedures have been assembled to make the set-up of the Recumbent Exercise Bikes as quick and easy as possible. Please take special note of the following important points prior to choosing a location and beginning assembly of the Recumbent Exercise Bikes. IMPORTANT SAFETY INSTRUCTIONS! . DO NOT locate the Recumbent Exercise Bike outdoors, near swimming pools, or in areas of high humidity. . DO NOT operate your Recumbent Exercise Bike if it has been dropped, damaged, or even partially immersed in water. Contact Life Fitness Customer Support Services at the number in the Operation Manual. . DO NOT locate the Recumbent Exercise Bike any closer than 30 inches (76 cm) to a television set. . DO NOT locate additional Recumbent Exercise Bike any closer than a minimum of 42 inches (107 cm) from center to center to avoid interference (cross talk) between Heart Rate monitors. . DO keep the area around your Recumbent Exercise Bike clear of any obstructions, including walls and furniture. . DO verify the contents of the delivery carton against the accompanying Parts Listing prior to setting the cartons and shipping material aside. If any parts are missing, contact Life Fitness Customer Support Services at the number listed in the Operation Manual. Save the shipping cartons in case of return. . DO read the entire Operation Manual prior to attempting to operate this machine as this is essential for proper use. . NE PAS placer le velo d’exercice allonge Lifecycle a l’exterieur, pres d’une piscine ou dans un endroit tres humide. . NE PAS faire fonctionner le velo d’exercice allonge Lifecycle s’il est tombe, s’il a ete endommage ou s’il a ete partiellement plonge dans l’eau. Telephoner au service apres-vente de Life Fitness dont le numero figure sur la couverture arriere du guide d’installation. . NE PAS placer le velo d’exercice allonge Lifecycle a moins de 76 cm (30 po) d’un poste de television. . MAINTENIR la zone autour du velo d’exercice allonge Lifecycle libre de toute obstruction, y compris murs et meubles. . VERIFIER si l’emballage contient toutes les pieces de la liste jointe avant de le mettre de cote. Si des pieces manquent, telephoner au service apres-vente de Life Fitness dont le numero figure sur la couverture arriere du guide d’installation. Conserver l’emballage au cas ou l’appareil devrait etre renvoye. . LIRE le manuel de l’utilisateur tout entier avant d’essayer de faire fonctionner cet appareil. Ceci est indispensable a son utilisation correcte. TOOLS REQUIRED FOR ASSEMBLY...Phillips screwdriver, 3/16" hex key wrench, T-40 Torx wrench PARTS DESCRIPTION 1 Seat Back Screw 0017-00101-1131 Qty: 4 2 Seat Back Washer 0017-00104-0253 Qty: 4 3 Console Support Assembly Bolt 0017-00101-1737 Qty: 4 4 Console Screw 0017-00101-1253 Qty: 4 5 Seat Back Qty: 1 6 Console Support Assembly AK39-00003-0000 Qty: 1 7 Display Console Qty: 1 8 Accessory Tray Assembly (If so equipped) Qty: 1 9 Left Pedal Strap Qty: 1 10 Right Pedal Strap Qty: 1 11 9V Battery (Model 8500 Only) 0017-00003-0757 Qty: 1 21 43 1” 2” 3” 4” 5” 7 8 5 2 1 6 4 3 11 9 10 1. Slide the ACCESSORY TRAY (#8) (if so equipped) over the user right seat back post and down to make contact with the SEAT HANDLEBAR. 2. Position the underside clamp bracket (A) around the SEAT HANDLEBAR and tighten the two clamp SCREWS and WASHERS (B). NOTE: BE CAREFUL NOT TO OVER-TIGHTEN THE SCREWS. MISE EN GARDE : VEILLER A NE PAS TROP SERRER LA VIS. 3. Align the four holes in the SEAT BACK (#5) with those in the SEAT BACK POSTS. Insert the four SCREWS (#1) and WASHERS (#2) through the backside of the SEAT BACK POSTS and into the SEAT BACK. Tighten the four SCREWS with a hex key wrench. NOTE: BE CAREFUL NOT TO OVER-TIGHTEN THE SCREWS. MISE EN GARDE : VEILLER A NE PAS TROP SERRER LA VIS. 4. Unfold the CONSOLE WIRE HARNESSES (C) from the POST extending from the FRAME. 5. Feed the WIRE HARNESSES at the top of the FRAME POST through the bottom of the CONSOLE SUPPORT ASSEMBLY COLUMN. Continue pushing the WIRE HARNESSES until the CONNECTORS at the end of the WIRE HARNESSES exit through the opening at the top of the COLUMN. Gently pull the WIRE HARNESSES to remove the slack. 6. Position the CONSOLE SUPPORT ASSEMBLY (#6) so that the HANDLEBAR is facing the user and slide the CONSOLE SUPPORT ASSEMBLY into the FRAME POST (D), being careful not to pinch the WIRES in the process. Align the holes in the top of the CONSOLE SUPPORT ASSEMBLY with those in the FRAME POST. Install the four CONSOLE SUPPORT ASSEMBLY BOLTS (#3) to secure it into position. Tighten the four CONSOLE SUPPORT ASSEMBLY BOLTS to 15-20 ft. lbs. NOTE: BE VERY CAREFUL NOT TO DAMAGE THE WIRES WHEN PASSING THE BOLTS THROUGH THE HOLES. TIGHTEN THE BOLTS SECURELY. MISE EN GARDE :FAITES ATTENTION TRES A NE PAS ENDOMMAGER LES FILS EN PASSANT LES BOULONS PAR LES TROUS. SERREZ LES BOULONS SOLIDEMENT. 7. Align the LOCKING TABS of the 10-PIN CONNECTOR and the 4-PIN CONNEC...