Seeing conditions often preclude the use of the 5.2, so I sometimes substitute the 7. It can be used a bit more often, but doesn’t provide quite the detail of the 5.2 when seeing is really good. The view through the 40mm is spectacular on extended objects. Its 2° field is almost half that of many finder scopes, making a finder scope unneccessary. Fig 23: My Accessories Drawer Pentax XL Eyepieces Red LED Flashlight Eyepiece Heater Laser Collimator 14 Holding the Eyepiece in Place The clamping scr

Example: Setting the temperature to +22°C Press [F4] [CORR] in mode B. (If the instrument is in mode A, press [F5] [MODE] to enter mode B.) Press [F4] [h] to move the cursor to “3.TEMP” and press the [F5] [SELECT] to enable the temperature to be changed. Clear the exiting values by pressing [CLEAR] key. Input 22 by pressing the numeric keys. CORRECTION 1.PRISM CONST 0mm 2.SHEET CONST 0mm 3.TEMP : +15°C 4.PRESS : 1013hPa 5.ppm 0ppm 1.PRISM CONST 0mm 2.SHEET CONST 0mm 3.TEMP : +15°C 4.PRESS : 1013

• If water should happen to splash on the instrument or the battery, wipe it off immediately and allow it to dry in a dry location. Do not put the instrument in the case until it is completely dry as this may result in damage to the instrument. • Turn off the power when removing the battery from the instrument as removing the battery while the power is still on may result in damage to the instrument. • The battery mark displayed on the instrument is only an estimate of remaining battery power an

Do not throw the battery into fire or expose it to heat as there is a risk of Injury if it explodes. P1 PRECAUTIONS REGARDING SAFETY........ CAUTION For security, please do the opening inspection and inspection every a fixed period and adjustment. When the laser beam enters eyes, an unexpected accident might be caused by the blink of eyes. Establish the laser product to avoid the height of eyes of a driving person and walker. Establish an instrument so that laser beam does not hit a reflection t

53 8-2 Entering the Mode for Initial Setting 1 .............................................. 53 8-3 Entering the Mode for Initial Setting 2 .............................................. 53 8-4 Entering the Mode for Initial Setting 4 .............................................. 54 8-5 Entering the Mode for Initial Setting 5 .............................................. 54 8-6 Example of Changing an Initial Setting Content .............................. 55 8-7 Initial Setting 1 ..............

This mark can be used to check the charge status of the battery. 2 1 Plenty of charge left 1 2 2 2 1 Plenty of charge left 1 2 2 1.4 Attaching and charging the battery [Removing the battery] Turn the lock lever anticlockwise and remove the battery. Lift up the battery pack and remove it from the instrument. 2 1 • Be absolutely sure to turn the power off when removing the battery as removing the battery while the power is still on may result in damage to the instrument. 1 3 Get the spare battery

PRECAUTIONS REGARDING SAFETY Safety Precautions (Must be followed) The following items are intended to prevent possible injury to the user or other people and/or damage to the instrument before it occurs. These safety precautions are important to the safe operation of this product and should be observed at all times. Distinctive Displays The following displays are used to distinguish precautions by the degree of injury or damage that may result if the precaution is ignored. WARNING Items indicat

Unsuitable Condition ERROR!! EDM ERROR 04 -05, 34-39, 50-53 ERROR!! ETH ERROR 7076 ERROR!! ETH ERROR 19 ERROR S DATA of EDM ERROR P DATA of EDM ERROR ETH DATA Meaning Displayed when the instrument is tilted beyond the vertical compensation range (±3') in case 1 axis or 2 axis automatic compensation is selected. This message may be temporarily displayed if the instrument is turned too fast. The input data exceeds the allowable range. The distance is measured by Prism at Reflector sheet mode, and

Confirm the alignment (horizontal and vertical ) before measuring when performing accurate work like stake out when using the Laser pointer function. Also refer to 10-10. The EDM beam axis. • Please do not look at the laser source of beam directly. 3. PREPARATION FOR SURVEYING 3.1 Centering and leveling of the instrument [Setting up the instrument and the tripod] 2 1 Adjust the tripod legs so that a height suitable for observation is obtained when the instrument is set on the tripod. Hang the pl

Please note that the movement of the vial becomes opposite direction if it sees at the position of ..Right circle position". .. When instrument is within the tilt compensation range, length and sidewise..3', “ON” is displayed at the right screen, “ OVER” is displayed beyond the limits of range and “NIL” is displayed at no compensation setting. .. With command No "520" or "Initial setting 2", when the [TILT DISP] is selected as ON, the [F1 -TILT] of the vial screen becomes effective. The Vial til