NO. 1690404 NOTE NOTE This kit cannot be used on tractors equipped with a An electric lift is recommended for 38" rotary tiller. Vickers hydrostatic pump. The kit may be used with either the manual lift lever or power lift kit. FRONT OF TRACTOR PTO BRACKET GUARD PULLEY (K) AND GUARD (I) NOT USED WITH 38" ROTARY TILLERS tr® A. Lift Clevis L. B. Cotter Pin, 1/8x1 M. C. Hex Jam Nut, 3/8-24 N. D. Hex Locknut, 3/8-16 O. E. Cotter Pin, 3/32 x 3/4 P. F. Lift Cable Assy. Q- G. Pivot Pin R.

• Safety • Operation • Maintenance • Storage • Espanbl Sears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.A. Visit our website: FORM NO. 769-00054 Printed in U.S.A. (2/2002) Content Page Warranty Information ................................ 2 Safe Operation Practices .......................... 3 Slope Gauge ............................................ 6 Setting Up ................................................. 7 Operation ................................................. 9 Maintenance ....

These conditions are descdbed below. Read this section and be aware of the purpose of this safety mechanism at all times; do not tamper with its working. _lb WARNING:operate the ridingmower if the safety intedock To avoid serious injury, do not system is malfunctioning. The purpose of the safety intedock system is four-fold: a. to prevent the engine from starting unless the brake pedal is depressed; b. to shut off the engine if the blade control lever is not disengaged when the shiftlever is put

IMPORTANT:The V-belts, used on this vehicle, are specially designed to engage and disengage safely. A substitute (non-OEM) V-belt can be dangerous by not 20 disengagingcompletely.Foraproperworkingmachine, usebeltsavailablefromSears. 1. Follow Figure 25 for routing of belts and pulleys. 2. Periodically check to see if these belts are too loose or damaged through wear and tear. If so, replace with new belt. NOTE: It is recommended that both drive belts be replaced at the same time. Special tools r

Your life and the lives of others depend on it! © Copyright 2009 Printed 02/19/09 Cover photo may show optional equipment not supplied with standard unit. Table of Contents Part Number Index Section 1: Introduction.................................................4 Using This Manual...............................................................4 Manual Replacement Information.......................................4 Manual Revisions................................................................4

Part No. Part Description Comments Revision dwg21221 Drawing Image Number 815-143C RH DISC BRAKE ASM 172mm W/JNT (S/N 400270+) Does not include #3, Rev. 2 #4 & #5 700-256D RH DISC BRAKE ASM 1/6 TAPER (S/N 400269-) Does not include #3, Rev. 1 #4 & #5 815-144C LH DISC BRAKE ASM 172mm W/JNT (S/N 400270+) Does not include #3, Rev. 2 #4 & #5 700-257D LH DISC BRAKE ASM 1/6 TAPER (S/N 400269-) Does not include #3, Rev. 1 #4 & #5 1. 802-589C HHCS 7/16-14X2 GR5 2. 803-229C NUT HEX FLANGE LOC 7/16-14 PLT

Result: The machine should move in the direction that the blue arrow points on the drive chassis, then come to an abrupt stop. 48 Slowly move the drive control handle in the direction indicated by the yellow arrow on the control panel until the machine begins to move, then return the handle to the center position. Result: The machine should move in the direction that the yellow arrow points on the drive chassis, then come to an abrupt stop. Note: The drive brakes must be able to hold the machine

MAIN WIRING HARNESS NT (S/N 418339 to 440713) Rev. 2 not compat. w/Rev. 1 833-260C10. WIRING HARNESS TRUCK (S/N 418338-) N/A11. BATTERY BCI Group U1/U1R, min. 300CCA. See Note 1 833-277C12. TAILLIGHT Includes bulb 833-335C13. WIRE HARNESS INSTRUMENT PANEL (S/N 418339+) Rev. 2 not compat. w/Rev. 1 833-296C13. WIRING HARNESS INSTRUMENT PANL (S/N 418338-) 833-303C14. 20" 6GA NEGATIVE BLACK CABLE 833-338C15. 30 AMP RESETABLE CIRUIT BREAKR 839-288C16. 20 AMP FUSE (5 PACK) 840-105C17. PUSH RETAINERS 4

5. 710-097D KEY 3/16 X 3 6. 790-001A TREKER ENGINE/TRANS ALIGNMENT Optional 7. 800-235C SPRING CLAMP 1" OD HOSE 8. 800-259C CLAMP WRM DRV#36SS (1.81-2.75) 9. 800-350C KEY .187 X .247 X 2.5 LG 10. 801-180C TPHMS Y 1/4-20X3/4 YELLOW DIE 11. 801-197C HSFHCS 5/16-24 X 3/4, BLK 12. 801-199C SCR SELF TAP #10 X 3/4 13. 802-005C HHCS 1/4-20X1 GR5 14. 802-320C HHCS 1/2-20X2 GR5 15. 802-738C HHCS 5/16-18X1 GR5 YELLOW DIE 16. 802-770C HHCS 3/8-24X3 1/2 GR5 PLT 17. N/A INSERT, 1/4-20 ARS4-420-280 Included w