Оценок - 3, средний балл: 3.3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
8 Administrator Password Enter the Administrator password that was specified on the CL console. If this password is not entered correctly, it will not be possible to synchronize from CL Editor to the CL console. CL Editor Owner’s Manual 2 9 9 Press this button to use the settings (except for the IP Address in the Network section) currently specified in the System Setup dialog box as the default settings. The next time when you start up CL Editor, it will use these settings. . Mixer Setup To open the Mixer Setup dialogbox, choose [Mixer Setup] from the [File] menu. 1 Mix Bus Setup Here you can make settings relating to the MIX buses. Signal Type: Choose either MONOx2 or STEREO for each 1 two adjacent odd-numbered/even-numbered MIX buses. Bus Type/Send Point: Choose either VARI (PRE FADER) or VARI (PRE EQ) or FIXED for each two adjacent odd-numbered/even-numbered MIX buses. Pan Link: The PAN setting for signals sent to stereo MIX buses will link to the PAN setting for the STEREO bus. This parameter is valid only if the Signal Type is set to STEREO and the Bus Type is set to VARI. 2 Matrix Bus Setup Here you can make settings relating to the MATRIX buses. Signal Type: Choose either MONOx2 or STEREO for each 2 two adjacent odd-numbered/even-numbered MATRIX buses. Send Point for Input Channels: Choose either PRE FADER or PRE EQ for each two adjacent odd-numbered/ even-numbered MATRIX buses. Pan Link: The PAN setting for signals sent to stereo MATRIX buses will link to the PAN setting for the STEREO bus. This parameter is valid only if the Signal Type is set to STEREO. CL Editor Owner’s Manual 3 . . To open the Create User Key dialogbox, choose [Create User Key] from the [File] menu. This creates a user key (with “.CLU” file name extension) that can be read from a USB flash drive by the CL console to automatically set user-specific parameters. 234165780A9 E FDC B 1 User Name Specify the name of the user. You can enter up to eight single-byte alphanumeric characters. Lowercase characters will automatically become uppercase on the CL console. 2 Comment Enter a comment for each user. You can enter up to thirty-two single-byte alphanumeric characters. 3 Password Enter a password that will be used when this user key is read by the CL console. You can enter up to eight single-byte alphanumeric characters. Uppercase and lowercase are distinguished. 4 Re-Enter Password Enter the password once again as a safeguard against mistaken entry. 5 POWER USER Specify whether this user is a power user. Power users can use the CL console to create or edit a user authentication key with a specified user level. 6 Administrator Password Enter the Administrator password that was specified on the CL console. This is not required if no Administrator password has been specified on the CL console, but if this password is incorrect you will be asked to enter it when the user key is read. 7 ACCESS PERMISSION In this area, specify the parameters that this user will be allowed to operate. CL Editor Owner’s Manual 4 8 8 INPUT, ST IN, MIX, MATRIX, ST/MONO, DCA: Select the channels whose parameters will be operable. HA: Change the operating privileges for the head amp gain (analog gain) and phantom power of the selected channels. PROCESSING: Change the operating privileges for overall signal processing parameters (except for fader and [ON] button) of the selected channel. For the specific parameters included in PROCESSING, refer to the CL’s man ual. FADER/ON: Change the operating privileges for the pan/balance, fader, channel on, send on/off, and send level of the selected channels. Set All: Turn on HA, PROCESSING, and FADER/ON for all channels. Clear All: Turn off HA, PROCESSING, and FADER/ON for all channels. Set by One Click: If this button is on, pressing the channel select button repeatedly will set HA, PROCESSING, and FADER/ON to On or Off simultaneously. 9 SCENE LIST STORE/SORT: Change the operating privileges for scene store and sort operations. RECALL: Change the operating privileges for scene recall operations. 0 LIBRARY LIST STORE/CLEAR: Change the operating privileges for library store and clear operations. RECALL: Change the operating privileges for library recall operations. A FILE LOAD USER SETUP: Change the operating privileges for loading user-defined keys and preferences when loading a file. SYSTEM SETUP MONITOR SETUP: Change the operating privileges for loading system setup and monitor setup settings when loading a file. CURRENT SCENE: Change the operating privileges for loading the current scene when loading a file. SCENE LIST: Change the operating privileges for loading the scene list when loading a file. LIBRARY LIST: Change the operating privileges for loading the library list when loading a file. B CURRENT SCENE INPUT PATCH: Change the operating privileges for input patch operations. INPUT NAME: Change the privileges for editing the input names. OUTPUT PATCH: Change the operating privileges for output patching. OUTPUT NAME:...
Эта инструкция также подходит к моделям:Музыкальные инструменты - CL3 (3.2 mb)
Музыкальные инструменты - CL5 (3.2 mb)