Оценок - 2, средний балл: 3.5
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
The "Internet Protocol Version 4(TCP/IPv4) Protocol" dialog box will be displayed. 5. Click [Obtain an IP address automatically]. 6. Click [OK]. .Windows XP 1. Select [Start] > [Control Panel]. The "Control Panel" is displayed. 2. If the control panel appears as category view, click [Switch to Classic View]. 3. Double-click [Network Connections] > [Local Area Connection]. The "Local Area Connection Status" dialog box will be displayed. NOTE .If the "Local Area Connection properties" dialog box appears, skip ahead to step 5. 4. Click [Properties]. The "Local Area Connection Properties" dialog box will be displayed. 5. Select [Internet Protocol (TCP/IP)], then click [Properties]. The "Internet Protocol (TCP/IP) Properties" dialog box will be displayed. 6. Click [Obtain an IP address automatically]. 7. Click [OK]. ¦ Updating the CL series firmware Described below are the procedures to update the CL series unit firmware. Uncompress the compressed file you downloaded in advance. 1. Save the CL internal data to the USB memory or CL Editor (compatible with the current firmware version) as backup. If you are saving the data to the USB memory, open the SAVE/LOAD popup window from the SETUP screen. 2. Turn off the power to the CL series. 3. Remove the cable connected to the Dante connector. When it initializes, a setup of Dante may change from REDUNDANT to DAISY CHAIN. If it changes to a setup of DAISY CHAIN with REDUNDANT connection, it will be in the state where communication is impossible. Please carry out re-connection of the cable after update is completed and returning a setup. 4. Connect the USB memory (formatted in FAT12/FAT16/FAT32) to the USB connector of your computer. 5. Copy the files (extensions .PGM and .BIN) in the "cl_frm***" (*** indicates the version number) folder extracted from the downloaded file to the root directory of the USB memory. 6. Remove the USB memory when the files have been copied. For more information on removing the USB memory, refer to the owner's manual for your computer and USB memory. 7. Connect the USB memory to the CL USB connector, then turn on the power to the CL series. A "Start Loading ?" message will be displayed. 8. Click the OK button to start loading the firmware. CAUTION:A "Loading..." message will appear during loading the firmware. Progress from 0 to 100% is repeated 3 times. Do not disconnect the USB memory or power-off the CL series while accessing the USB memory. 9. When the firmware has been loaded, the CL series automatically restarts and a "Starting System..." message flashes for approximately one minute. While this message is flashing, do not turn off the power. If you have accidentally turned off the power, turn on the power again to resume the initialization. 10. When a "Since CL was upgraded, Initialize all memories" or “Memory Error! Current Memories were Initialized.” popup window (or similar message) appears, press the CLOSE button to close it. NOTE .Since it is a message about initialization even if displayed as an error, please continue update. 11. When an "Initialize All Memories ?" message appears, press the INITIALIZE button. 12. When an "Are you sure ?" message appears, press the OK button. Initializing the internal memory will be started. 13. When the initialization is complete, press the EXIT button. 14. Remove the USB memory after confirming the ACCESS indicator has disappeared in the function access area. 15. If necessary, confirm the firmware was correctly updated in the version field in the SETUP screen. Also, adjust the detection point of the touch screen (Calibration function) on the startup menu screen. Restart the CL series first to adjust the faders (Calibration function). ¦ Updating the Dante firmware Described below are the procedures to update the Dante module firmware integrated in the CL series unit. NOTE .For details of the Dante Firmware Update Manager, refer to “User Guide Dante Firmware Update Manager" stored in the compressed file folder. 1. Connect the Dante [PRIMARY] connector on the rear panel of the CL series unit to the Ethernet connector on the computer using an Ethernet cable. Be sure to directly connect the computer and the CL series unit, and do not connect any other Dante device to the computer. 2. Select [Start]>[All programs]>[Audinate]>[Dante Firmware Update Manager]>[Dante Firmware Update Manager ]. The Dante Firmware Update Manager will start up. Check that the version number is 1.0.6 or higher from the title bar. NOTE .When running under Windows 7, the "User Account Control" dialog box may appear. Click [Continue] or [Yes]. 3. Click [Update Dante Firmware]. 4. Click [Browse] and select “FWUpdate_CL5_vxxx_swyyy.dnt" if it is CL5, “FWUpdate_CL3_vxxx_swyyy.dnt” if CL3 or “FWUpdate_CL1_vxxx_swyyy.dnt" if CL1. Then click [Open]. xxx and yyy represent the firmware version number. NOTE .The Dante firmware does not operate normally if its path contains any multi-byte character (including Japanese characters). If you u...
Эта инструкция также подходит к моделям:Музыкальные инструменты - CL3 (243.27 kb)
Музыкальные инструменты - CL5 (243.27 kb)