Оценок - 2, средний балл: 3
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
You can temporarily disable a Fader group in order to make adjustments to individual fad ers by touching two or more faders in the group, or by operating the fader while holding down its [SEL] button. Fader groups are active only in Fader mode. See “Selecting Fader Modes” on page 35 for more information. 02R96—Owner’s Manual Grouping Output Channel Mutes (ON/OFF) 107 Grouping Output Channel Mutes (ON/OFF) 107 The Bus Out, Aux Send, and Stereo Out mutes can be grouped, allowing you to mute several Output Channels simultaneously. There are four Output Channel Mute groups: U, V, W, and X. 1 Use the DISPLAY ACCESS [GROUP] button to locate the Output Mute Group page. 2 Press the LAYER [MASTER] button. 3 Use the Up/Down cursor buttons to select Mute groups U–X. The selected group is highlighted by a flashing cursor box. 4 Use the [SEL] buttons to add and remove Output Channels to and from the selected group. When an Output Channel is added to a Mute group, its [SEL] button indicator lights up. ENABLE: These buttons are used to enable and disable the groups. Mute groups may contain a combination of channels that are on and channels that are off. 02R96—Owner’s Manual 108 Chapter 11—Common Channel Functions 108 Chapter 11—Common Channel Functions The parameter setting of the currently selected Input Channel, Bus Out, Aux Send, or the 1 Stereo Out can be viewed and set on the Parameter View pages. Use the DISPLAY ACCESS [VIEW] button to select the Parameter View page. 2 Use the LAYER buttons to select Layers, and use the [SEL] buttons to select channels. 3 Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] buttons to set them. Input Channels This is the Parameter View page for the Input Channels. GATE: The following Gate parameters for the currently selected Input Channel can be set: Gate On/Off, Threshold, Range, Attack, Decay, and Hold. The GR meter indicates the amount of gain reduction being applied by the Gate. Also displayed are the gate curve and gate type. See “Gating Input Channels” on page 60 for more information. COMP: The following Compressor parameters for the currently selected channel can be set: Comp On/Off, Threshold, Ratio, Attack, Release, Gain, and Knee. The GR meter indicates the amount of gain reduction being applied by the Compressor. Also displayed are the comp curve and comp type. See “Compressing Channels” on page 97 for more information. INSERT: The currently selected channel’s Insert can be turned on and off and patched. See “Using Inserts” on page 95 for more information. EQ: The currently selected channel’s EQ and Attenuator can be set. Also displayed is the EQ curve of the currently selected Input Channel. See “Using EQ” on page 91 for more information. Meters: These meters indicate the levels of the currently selected channel and its horizon tal or vertical partner. Phase: The signal phase of the currently selected Input Channel can be reversed. See “Reversing the Signal Phase” on page 59 for more information. DELAY: The currently selected channel’s Delay function can be set. See “Delaying Channel Signals” on page 101 for more information. PAIR: This heart icon indicates whether or not channels are paired. See “Pairing Channels” on page 104 for more information. 02R96—Owner’s Manual Viewing Channel Fader Settings 109 Viewing Channel Fader Settings 109 This is the Parameter View page for the Bus Outs, Aux Sends, and the Stereo Out. Parameters are the same as for the Input Channel Parameter View page, minus the GATE and Phase sections and the DELAY MIX and FB GAIN parameters. The parameter settings of the left and right channels of the Stereo Out can be viewed individually. Use the [SEL] buttons to toggle between the left and right channels. Viewing Channel Fader Settings The fader-related settings of the currently selected Input Channel, Bus Out, Aux Send, or the Stereo Out can be viewed and set on the Fader View pages. 1 Use the DISPLAY ACCESS [VIEW] button to select the Fader View page. 2 Use the LAYER buttons to select Layers, and use the [SEL] buttons to select channels. 3 Use the cursor buttons to select the parameters, and use the Parameter wheel, INC/DEC buttons, and [ENTER] buttons to set them. Pan and Balance controls can be set to center by pressing [ENTER] while they’re selected. Input Channels This is the Fader View page for the Input Channels. PAN: This is the currently selected Input Channel’s Pan parameter. See “Panning Input Channels” on page 67 for more information. ON/OFF: This is the On/Off parameter of the currently selected Input Channel. See “Muting Input Channels (ON/OFF)” on page 63 for more information. Fader: This indicates the fader position of the currently selected Input Channel. The fader knob appears highlighted when the fader is set to 0.0 dB. The fader position is displayed 02R96—Owner’s Manual 110 Chapter 11—Common Channel Functions 110 Chapter 11—Common Channel Functions mation. SURROUND PAN: The ...