Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
PUSH 1 Press 6 PUSH OPEN/CLOSE OPEN/CLOSE down to open the CD compartment and place the CD on the CD compartment. With the label side up 2 PUSH Close the lid of the CD OPEN/CLOSE compartment. 3 Press ^ (direct power-on). Display The player plays all the tracks once. Track number Playing time Basic Operations Tip Next time you want to listen to a CD, just press ^ . The player turns on automatically and starts playing the CD. Use these buttons for additional operations POWER 6 PUSH OPEN/CLOSE VOLUME +, – ^ p + = To Press adjust the volume VOLUME +, – (VOL +, – on the remote) stop playback p pause playback ^ (P on the remote) Press the button again to resume play after pause. go to the next track + go back to the previous track = remove the CD 6 PUSH OPEN/CLOSE turn on/off the player POWER Basic Operations Basic Operations Listening to the radio 12 2 For hookup instructions, see pages 23 - 24. 1 1 BAND Press BAND until the band you Display PRESET PRESET want appears in the display (direct power-on). 2 Hold down TUNING/TIME SET Indicates an FM stereo + or – until the frequency digits broadcast. begin to change in the display. TUNING/TIME SET The player automatically scans the radio frequencies and stops when it finds a clear station. If you can't tune in a station, press the button repeatedly to change the frequency step by step. Basic Operations Tips • If the FM broadcast is noisy, press PLAY MODE•MONO/ST ISS until “Mono” appears in the display and the radio will play in monaural. • Next time you want to listen to the radio, just press BAND. The player turns on automatically and starts playing the previous station. Use these buttons for additional operations PLAY MODE MONO/ST ISS VOLUME + , –POWER To Press adjust the volume VOLUME +, – (VOL +, – on the remote) turn on/off the radio POWER To improve broadcast reception FM Keep the FM wire aerial as horizontal as possible (see page 24). AM Keep the AM loop aerial (supplied) away as far as possible from the player and then reorient the aerial (see page 24). Basic Operations Basic Operations Playing a tape 12 For hookup instructions, see pages 23 - 24. 1 Press p6 to open the tape With the side you want to play facing you compartment and insert a recorded tape. Use TYPE I (normal) tape only. Close the compartment. 2 Press ( . Display The player turns on (direct power-on) and starts playing. Basic Operations Tip Next time you want to listen to a tape, just press ( . The player turns on automatically and starts playing the tape. Use these buttons for additional operations POWER VOLUME +, – p6 P 0 , ) To Press adjust the volume VOLUME +, – (VOL +, – on the remote) stop playback p6 f ast-forward or rewind the tape ) , 0 pause playback P Press the button again to resume play after pause. eject the cassette p6 turn on/off the player POWER Basic Operations Basic Operations Recording on a tape 3 1 For hookup instructions, see pages 23 - 24. 1 Press p6 to open the tape With the side you want to record on facing you compartment and insert a blank tape. Use TYPE I (normal) tape only. 2 Select the program source you want to record. Display To record from the CD player, insert a CD (see page 4) and press p on the CD section. BAND PRESET PRESET To record from the radio, press BAND and tune in the station you want (see page 6). Basic Operations Press r to start recording. (( is depressed automatically.) Tips • Adjusting the volume or the audio emphasis (see page 25) will not affect the recording level. • If the AM program makes a whistling sound after you've pressed r in step 3, press PLAY MODE• MONO/ST ISS repeatedly until the noise is at a minimum. • To erase a recording, proceed as follows: 1 Insert the tape whose recording you want to erase into the tape compartment. 2 Turn on the power. 3 Press FUNCTION repeatedly until “TAPE” appears in the display. 4 Press r . Use these buttons for additional operations PLAY MODE POWER MONO/ST ISS p6 P To Press stop recording p6 pause recording P Press the button again to resume recording. turn on/off the player POWER Basic Operations Basic Operations The CD Player Using the display DISPLAY ENTER MEMORY You can check information about the CD using the display. Checking the total track numbers and playing time Check the display in stop mode. If the CD has more than 10 tracks, “OVER 10” appears in the display. Total playing time Total track numbers Music calendar Checking the remaining time Press DISPLAY•ENTER MEMORY while playing a CD. The track numbers in the music calendar disappear after they are played. To display Press DISPLAY•ENTER MEMORY the current track number and the remaining time on the current track* once remaining time on the CD and the number of tracks left twice the current track number and playing time three times * For a track whose number is more than 20 the remaining time appears as “– –:– –”. The CD Player Locating a specific track You can quickly locate any track using the number buttons. You can also find a specific p...
Эта инструкция также подходит к моделям:Музыкальные центры - PMC-20 (353.7 kb)