Оценок - 2, средний балл: 4.5 ( )

Производитель: Campbell Hausfeld Размер: 14.49 mb Название файла: 4abaf64a-d1a6-1ca4-6977-c6e9eb3134a9.pdf Язык инструкции:

1. Engage the trigger safety latch. 2. Turn the unit off. 3. Remove the ignition cable from the spark plug. 4. Shut off the water supply. 5. Disengage the trigger safety latch and trigger the gun to relieve pressure. 6. Re-engage the trigger safety latch. 7. Before overnight storage, long term storage, or transporting unit, disconnect the water supply and turn off the fuel supply valve. 3. Disconnect the water supply and high pressure hose from the pump. 4. Allow the engine to cool. 5. Disconnect the spark plug wire and remove the spark plug. 6. Pour 1/2 oz. of engine oil into the spark plug hole. Never pull the ! WARNING starter rope on the engine when the spark plug is removed unless the spark plug hole is covered. Fuel vapor from the hole can ignite by a spark. 7. Place a rag over the spark plug hole and slowly pull the starter rope several times to distribute the oil. WINTERIZING INSTRUCTIONS 1. Follow and complete the Long Term Storage Instructions on Page 9. 2. Disconnect the spark plug wire. 3. Disconnect the high pressure hose from the pump. 4. Insert a 12” to 14” piece of garden hose into the pump inlet. 5. Place a funnel in the other end of the garden hose. 9 Pressure Washers Operation (Continued) Read the TIPS FOR EXTENDING THE LIFE OF spraying water can damage pumpNOTICE manufacturer’s YOUR PRESSURE WASHER components. instructions for safe handling and dis 1. Never operate the unit without 4. Release the trigger prior to switchposal of RV antifreeze. water. ing the lance between high and low 6. Pour approximately 6 oz. of RV pressure. Failure to do so may 2. Your pressure washer is not meant antifreeze into the funnel. reduce the life of the o-rings in the to pump hot water. Never connect 7. Pull the starter rope several times lance. your pressure washer to a hot water until the RV antifreeze comes out of supply as it will significantly reduce the pump outlet. the life of the pump. 8. Disconnect the high pressure hose 3. Running the unit for more than one from the gun and drain the hose. minute without spraying water Hold the gun and lance in a vertical causes heat to build up in the position and squeeze the trigger to pump. Running the unit without drain the water out. Maintenance Observe regular maintenance intervals to ensure maximum performance and life from the pressure washer. Refer to the schedule for recommended maintenance. If you operate the pressure washer in dusty conditions, perform maintenance checks more often. ENGINE OIL CHANGING INSTRUCTIONS Before tipping the ! CAUTION engine or equipment to drain oil, drain fuel from the fuel tank. NOTE: Change oil while the engine is cool. 1. Disconnect the spark plug wire from the spark plug. 2. Locate and remove the engine oil drain plug (see Figure 19). 3. Drain old oil. 4. Replace the drain plug and set the unit upright. 5. Refill the unit with new oil of a recommended type and quantity. Fill the unit to the proper level shown on the dipstick (if provided). Otherwise, fill the unit to the top of the oil filler neck. CHECKING PUMP OIL AND PUMP OIL CHANGING Checking oil level: Most pumps have either a sight glass or a dipstick (or both) to check the pump oil level. The sight glass is usually located on the back side of the pump. The dipstick has a plastic cap and is located at the top of the pump (See Figure 20.) Changing oil: Remove the oil drain plug located at the backside or bottom of the pump. (See Figure 20.)Drain old oil. Replace drain plug. Refill pump with the correct type and amount of oil (see page 11 for oil types and amounts). Check oil level. Upon starting the pressure washer check for any pump oil leaks. Oil drain Oil fill Drain plug Oil sight glass Oil dipstick Figure 19 - Oil drain and fill locations Figure 20 - Checking and changing pump oil 10 Maintenance (Continued) Maintenance Schedule Maintenance Schedule Action needed Each use • Check water inlet screen and filter. • Check engine and pump oil levels. Fill as necessary. • Check gasoline level. Fill as necessary. After first 5 hours of operation • Change engine break-in oil. Use SAE30 or 10W-30 detergent oil. After first 50 hours of operation • Change pump oil. Every 25 hours of operation • Change engine oil if operating under heavy load or high ambient temperature. • Remove and clean foam pre-cleaner or foam air filter (if applicable). Wash with water and mild detergent. Dry thoroughly. Rub with oil and squeeze to distribute oil. Every 50 hours of operation • Change engine oil. • Replace spark plug. Each 100 hours of operation or every 3 months • Clean or replace paper air cleaner cartridge. Tap gently to remove dirt. • Change engine oil. Every 500 hours of operation (5 months) • Change pump oil. Technical and Consumer Information Horizontal Oriented Pressure Washers Engine Oil Type SAE 10W-30 SAE 30W (Above 60O F) Engine Oil Capacity Briggs and Stratton Vanguard Series 7-8 HP 30 fl. oz. Vanguard Series 11-13 HP 51 fl. oz. Intek Series 8...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: