Оценок - 4, средний балл: 4 ( )

Производитель: Campbell Hausfeld Размер: 14.49 mb Название файла: Язык инструкции:

Never use a narrow high impact stream or a Turbo/rotary nozzle on a surface that is susceptible to damage. Avoid spraying windows with a narrow high impact stream or turbo nozzle. Doing so may break the window. The most sure way to avoid damaging surfaces is to follow these steps: 7 Pressure Washers Operation (Continued) 1. Before triggering the gun, adjust the nozzle or quick connect tip to a wide fan pattern. 2. Place the nozzle approximately 4-5 feet away from the cleaning surface. Then hold the nozzle at a 45 degree angle to the cleaning surface. Trigger the gun. 3. Vary the fan pattern spray angle and the distance to the cleaning surface until optimum cleaning efficiency is achieved without damaging the surface. TURBO NOZZLE (NOT INCLUDED WITH ALL MODELS) A turbo nozzle, sometimes referred to as a rotary nozzle, can significantly reduce cleaning time. The turbo nozzle combines the power of a narrow high impact stream with the efficiency of a 25 degree fan pattern. The turbo nozzle swirls a narrow high impact stream into a cone shape to clean a larger area. Since a turbo nozzle NOTICE uses a narrow high impact stream, only use a turbo lance in applications where the cleaning surface cannot be damaged by narrow high impact spray. The turbo nozzle is NOT adjustable and cannot be used to apply detergent. 4. Detergent Application USE THE INSTRUCTIONS APPROPRIATE FOR MODEL PURCHASED NOTE: Use only detergents formulated for pressure washers. NOTE: Test detergent in an inconspicuous area before use. Never slide the NOTICE nozzle from low to high pressure or from high to low pressure when the gun is triggered. Never replace quick ! WARNING connect tip when gun is triggered. DETERGENTS The use of detergents can dramatically reduce cleaning time and assist in the removal of difficult stains. Many detergents are customized for pressure washer use on specific cleaning tasks. Pressure washer detergents are as thick as water. Using thicker detergents – like dish soap – will clog the chemical injection system and prevent the application of the detergent. Once applied to a cleaning surface, detergents take time to break down dirt and grime. Detergents work best when applied at low pressure. You can effectively clean surfaces by combining the chemical action of detergents with high pressure rinses. On vertical surfaces, apply the detergent starting at the bottom and work your way upward. This method prevents the detergent from sliding down and causing streaks. Begin high pressure rinsing at the bottom and work your way upward. On particularly tough stains, use a brush in combination with detergents and high pressure rinsing. 1. Follow manufacturer’s label directions for mixing correct concentrations of soap/detergents. The soap detergent to water ratio through the pump is approximately 10% (1 to 10). 2. Insert the filter end of the clear plastic detergent tube into the detergent container. 3a. Place hand around the 3.5” spraying end section of the lance (the section Figure 16 - Quick Connect Tip that turns from left to right). Pull firmly and quickly away from you. (NOTE: Do not adjust lance while spraying.) The lance will extend 1/2” and be in low pressure (See Figure 18). Soap can only be drawn in low pressure. 3b. For units with quick connect tips: use the black 65o quick connect spray tip (See Figure 16). 4. If equipped, adjust the detergent injection flow by turning the collar of the injector. Turning collar clockwise decreases flow of detergent and turning collar counter clockwise increases detergent flow (See Figure 17). Figure 17 - Detergent injection adjust- ment GENERAL CLEANING TIPS 1. Apply the detergent so that it thoroughly covers the cleaning surface. Apply the detergent from bottom to top to prevent the detergent from Low Pressure High Pressure Figure 18 - Adjusting nozzle for pressure Nozzle 8 Operation (Continued) sliding down and streaking. Wait a couple of minutes for the detergent to break down the dirt and grime. Use a brush to lightly scrub heavily soiled areas. Never allow the detergent to dry on the cleaning surface. 2a. To rinse or to return the nozzle to high pressure, release the trigger and slide the nozzle to the high pressure setting. 2b. For units with quick connect tips: replace black 65o tip with another color tip. Never make the NOTICE nozzle pressure adjustment when the gun is triggered. Adjusting the high-low nozzle when the gun is triggered can result in damage to the seals in the nozzle. Never replace quick ! WARNING connect tip when gun is triggered. 3. After using detergents, flush the suction system by placing the detergent suction tube into a bucket of clean water. 5. Cleaning Power You can control the cleaning power of your pressure washer in two ways: 1. Adjust the spray pattern at the nozzle. Choose the widest pattern possible for spraying when starting the job and adjust the pattern to a narrower angle until you find a suitable pattern. 2. Th...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: