Оценок - , средний балл: ( )

Инструкция по эксплуатации Nilfisk-Advance America, модель P 150.2

Производитель: Nilfisk-Advance America
Размер: 1.28 mb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

2. Attach the nozzle. 4.3 Water connection An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. NOTE: Connection to the public mains according to regulations. IMPORTANT! Only use water without any impurities. If there is a risk of silt, sand or sediment in the inlet water (i.e. from your own well), an additional fi lter should be mounted. 1. Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the fi lter is fi tted in the water inlet pipe and that it is clean and free from debris. 2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 60°C). 3. Turn on the water. 4.4 Telescopic handle The machine features a telescopic handle. To raise or lower the handle, press the button (16) and move the handle upwards or downwards. When a click is heard, the handle is in right position. Nilfisk P 130.2 / P 150.2 / P 160.2 EN 4.5 Start and stop of the machine (when connected to a water supply) 4.6 Start the machine (when connected to open containers (suction mode)) 4.7 Pressure regulation on the TORNADO® PR- nozzle The spray lance is affected by a thrust during operation - therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground. 1. Check that the machine is in upright position. NOTE: Do not place the machine in tall grass! 2. Release the trigger lock. 3. Activate the trigger of the spray handle and let the water run until all air has escaped from the water hose. 4. Turn the start/stop switch (1) to position "I". 5. Activate the trigger of the spray handle. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be The washer can take in water from a rain water tank as an example. The hose for the water supply must not be too long, approx. 5 m. Make sure that the water tank is not placed on a lower level than the machine. Use an external filter if the water contains impurities. 1. Make sure that the water hose is filled completely with water before connecting to High pressure Low pressure cleaned. Do not cover the machine during operation. Note: If the ma chine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1): 1. Turn the start/stop switch to position "O". 2. Disconnect the electrical plug from the socket. 3. Shut off the water supply and activate the trigger to relieve the machine of pressure. 4. Lock the spray handle. When releasing the trigger of the spray handle, the machine automatically stops. The machine will start again when you re-activate the spray handle. the machine. Place the entire hose in a tank or bucket. To avoid water spillage, crimp the water inlet hose down in the water and then connect the hose to the machine with the quick coupling and fi nally uncrimp the water inlet hose. 2. Dismount spray handle, lance and nozzle. 3. Turn the start/stop switch to position "I" and let the water run, until the air has escaped from the water hose and the pump. 4. Mount spray handle, lance and nozzle again. The pressure can be regulated on the TORNADO® PR nozzle. 9 10 Nilfisk P 130.2 / P 150.2 / P 160.2 EN 4.8 Operation with detergents Application of detergents is NOT possible if an extension hose is applied. 1. Fill the container with a detergent. 2. Mount the TORNADO® PR nozzle and adjust it to low pressure (see section 4.7). 3. Adjust the dosing regulator (12) to the re quired vol ume of detergent (0-5%). 4. Apply the detergent from below and up wards. 5. Let the detergent act for the time stated on the packing of the detergent and fl ush with pure water. Separate detergent container 1. Remove the cover with suction hose from the detergent container. 2. Mount the cover with suction hose on the separate detergent container. The cover has a standard thread and fi ts common detergent containers. If your container does not have a standard thread, detach the fi lter from the suction hose and remove the cover. Remount the fi lter in the suction hose. Extra detergent hose can be pulled out of the machine. . 4.9 Stationary use If mounting a special wall hook (not standard), the pressure washer can be used as a stationary solution meaning that it can be operated while hanging on the wall. Only mount the wall hook on a sturdy wall. Adjust the length of the screws and size of rawlplugs to the type of wall. On the wall hook garden/rim brush (a), brush (b) and nozzles (c) can be stored. Important: The bearing capacity of the wall hook is max. 30 kg. a b c Nilfisk P 130.2 / P 150.2 / P 160.2 5 Fields of application and working methods EN 5.1 General Efficient high presure cleaning is achieved by following a few guidelines, combined with your own personal experience of specific cleaning tasks. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information a...