Войти:
Оценок - 2, средний балл: 4 ( )

Инструкция по эксплуатации Hamilton Beach, модель 3000 SERIES 3025

Производитель: Hamilton Beach
Размер: 384.42 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Load cells and weigh bars should be kept clean, dry & lubricated to insure dependability. Normal scale activity: Some warm up scale drift may occur after the scale is turned on but should zero balance within 10-15 minutes. Scale may zero shift over night due to temperature changes. Weight may change slightly due to terrain changes when mixer is moved. Vertical check bolts must not be tight (and should be free to rotate by hand) and need not less than 1/16” and no more than 3/32” free play when properly adjusted on level ground. Check arm assembly must be free to slightly rotate by hand when mixer is on level ground (see diagram), with mounting bolts tight. PIN CHECK BEARING should be centered on the pin when mixer is on level ground. Adjustment can be made by loosening the mounting bolts, centering pin check assembly on the pin and tightening the mounting bolts. If bushing cannot be centered load cells may require adjustment. INSPECTION & ADJUSTMENTS ALWAYS STOP MIXER AND LOCK OUT POWER BEFORE SERVICING, REPAIRING, OR CLEANING. IF WORK MUST BE PERFORMED INSIDE THE MIXER, STOP MIXER AND LOCK OUT POWER AND PUT A PROTECTIVE COVER OVER THE AUGER KNIVES TO AVOID INJURY. THE HOPPER FLOOR MAY BE SLIPPERY, AND THE REEL AND AUGERS WILL SPIN WHEN STEPPED ON. USE CAUTION WHEN STEPPING OR STANDING INSIDE THE UNIT. USE SAFE SHOP PROCEDURES AND EXERCISE CAUTION WHEN WORKING ON THIS MIXER! 3000STOPR005810R082503 INSPECTION & ADJUSTMENTS ALWAYS STOP MIXER AND LOCK OUT POWER BEFORE SERVICING, REPAIRING, OR CLEANING. IF WORK MUST BE PERFORMED INSIDE THE MIXER, STOP MIXER AND LOCK OUT POWER AND PUT A PROTECTIVE COVER OVER THE AUGER KNIVES TO AVOID INJURY. THE HOPPER FLOOR MAY BE SLIPPERY, AND THE REEL AND AUGERS WILL SPIN WHEN STEPPED ON. USE CAUTION WHEN STEPPING OR STANDING INSIDE THE UNIT. USE SAFE SHOP PROCEDURES AND EXERCISE CAUTION WHEN WORKING ON THIS MIXER! HAY MAXX SYSTEM adjustments Basic HAY MAXX SYSTEM must be bolted in the fully extended upright position if not equipped with optional hydraulic cylinder. HAY MAXX SYSTEM equipped with optional hydraulic cylinder can be adjusted with the clevis on the cylinder so that when the cylinder is fully extended the pan is in the upright position and when the cylinder is retracted the pan is completely down. Adjusting the knife to pan tolerance may be necessary for different types of feedstuff. As hay may vary in quality, moisture and material, each of these can affect how it goes through the HAY MAXX system. The pan can be adjusted to up to 1” from the knife for a more aggressive faster take through and will greatly increase the power required to operate. The factory setting is at 1/2”- 5/8” and should never be adjusted to less than 1/2” apart or greater than 1”. Field testing shows that 1/2” -5/8” is best for most materials. To adjust: loosen bolts, 3 in front & 2 at rear at the locations shown, make adjustment then securely tighten all five bolts. 3000STOPR005810R082503 LUBRICATION ALWAYS STOP MIXER AND DISCONN...

Эта инструкция также подходит к моделям:
Миксеры - 3000 SERIES 3015 (384.42 kb)
Миксеры - 3000 SERIES 3015 (384.42 kb)
Миксеры - 3000 SERIES 3020 (384.42 kb)
Миксеры - 3000 SERIES 3020 (384.42 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории