Оценок - 0, средний балл: 5
(
)
)
|
Фрагмент инструкции
Use a straight edge to verify the alignment of the sprockets. Inspect sprockets and chains. Replace if excessively worn. PROBLEM: FEED IS SEPARATING AS IT DISCHARGES FROM THE MIXER DOOR CAUSE SOLUTION DOOR IS OPEN LESS THAN HALF WAY Hay mixed in the load will separate from the grain if the discharge door is not open at least half way. Additional flow control plates may be required. 3000STOPR005810R082503 TROUBLE SHOOTING PROBLEM: OIL LEAKING AROUND THE EDGES OF THE OIL BATH CAUSE SOLUTION INSPECT SHIELD FOR LOOSENESS DAMAGED OR LOOSE GASKET MATERIAL AROUND ENCLOSURE SHIELD Carefully tighten wing nuts or adjust locking fasteners that hold shield in place, hand tighten only. Check for foreign material between the foam gasket and shield. Remove shield and check gasket material for proper adhesion to the mating panel of mixer. If gasket adhesive has come loose from front panel, replace gasket. PROBLEM: HYDRAULIC DOOR SYSTEM OPERATES ERRATICALLY CAUSE SOLUTION COMPONENTS STICKING OR BINDING INADEQUATE FLOW OR PRESSURE FROM HYDRAULIC SYSTEM. OIL IS LEAKING PAST SEALS IN CYLINDERS OR VALVES Check for hydraulic oil contamination, dirt, or gummy deposits. If dirt is found, search and repair the source. Check for worn or bent parts. Check oil level in hydraulic system. Check fluid and fill to proper level. Install seal kits to repair worn seals. See parts listing for part numbers. PROBLEM: SCALE HANGS UP, LOAD CELL ONLY CAUSE SOLUTION LOAD CELL NOT VERTICAL PIN CHECKOUT OF ADJUSTMENT SWING ARM NOT LUBRICATED Load cell should be vertical, if not first inspect check arm assembly and or pin check assembly. Second adjust by loosening top load cell mount in a no load condition, adjust load cell to a vertical position and tighten fasteners. Remove pin check assembly, test scale, if scale operates properly clean or repair pin check assembly. Also see “INSPECTIONS AND ADJUSTMENTS SECTION” lubricate check arm (should rotate on sockets without great effort). Also see “INSPECTIONS AND ADJUSTMENTS SECTION” PROBLEM: SCALE WEIGHS VERY HEAVY OR VERY LIGHT, WEIGH BAR ONLY CAUSE SOLUTION IMPROPER CALIBRATION DAMAGED CABLE ON ONE OR MORE LOAD CELLS CALIBRATE SCALE refer to scale operators manual for information Inspect cables and repair or replace as necessary. KUHN KNIGHT INC. 1501 West 7th Ave. Brodhead, WI 53520-0167 701 Cherry Ave. Greeley, Co. 80632 3000STOPR005810R082503 SPECIFICATIONS MODEL 3015 3020 3025 3030 Mixing Capacity Cubic Feet 147 216 250 300 Bushels 118 174 200 240 Approximate Weight (Empty lbs.) 2,850 4,890 6,489 7,021 Overall Dimensions O.A. Length, inches 113” 159” 160” 213” O.A. Width 87” 95” 97” 97” O.A. Height, inches 64” 64” 69” 69” Reel Diameter 52” 52” 60” 60” Lower Auger Diameter 16” 16” 18” 18” Upper Auger Diameter 14” 14” 18” 18” MODEL 3036 3042 3050 3060 3070 3095 Mixing Capacity Cubic Feet 360 420 500 600 700 950 Bushels 288 340 415 490 562 763 Approximate Weight (Empty lbs.) 8,480 8,800 11,788 13,599 17,295 20,500 Overall Dimensions O.A. Len...
Эта инструкция также подходит к моделям:Миксеры - 3000 SERIES 3015 (384.42 kb)
Миксеры - 3000 SERIES 3015 (384.42 kb)
Миксеры - 3000 SERIES 3020 (384.42 kb)
Миксеры - 3000 SERIES 3020 (384.42 kb)