.147495 Bump Knob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .180814 Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .753-1229 Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . .682075 For specific replacement parts, refer to the parts list located on the inside back cover of this manual. 25 SECTION 8: TROUBLESHOOTING GUIDE Trouble Possible Cause(s) Corrective Action ENGINE WILL • On/Off control in the STOP position • Turn On/Off control to ON NOT STA

Be sure the guard mounting bracket slides into the slot on the edge of the cutting shield. Rotate the shield into place, counterclockwise. The holes in the guard mounting bracket and cutting attachment shield will line up (Fig. 3). 2. From inside the cutting attachment shield, push the square bolt through the hole until the threaded end protrudes through the guard mounting bracket (Fig. 4). Guard Mounting Bracket Shaft Housing Square Bolt Cutting Attachment Shield 3. Put the washer on the bolt,

Dispose of the oil according to Federal, State and local regulations. 5. Refill the crankcase with 3.04 fluid ounce (90 ml) of SAE 30 SF, SG, SH oil. NOTE: Use the bottle and spout saved from initial use to measure the correct amount of oil. Pour fresh fuel into the bottle and fill it to the top of the label. The top of the label on the bottle measures approximately 3.04 ounces (90 ml). Check the level with the dipstick. If the level is low, add a small amount of oil and recheck. Do not overfill

Batteries discharge at a rate of about 1% per day. Charge the battery every six months even if it is unused to maximize battery life. Do not tape the trigger in the “ ON” position and leave the tool unattended as this may discharge the battery to a point where it will no longer be able to recharge. Store your battery pack in a cool, dry place. Do not store it in a place where the temperature will exceed 120° F (50°C) such as a vehicle or metal building during the summer. High temperatures will o

Never immerse trimmer head in water. 3. Regularly clean the trimmer line and spool housing using a soft brush or dry cloth. Care, Maintenance & Storage SAFETY & WARNING INSTRUCTIONS 34. Maintain the grass trimmer with care. Use only manufacturer’s replacement parts. Follow instructions for changing trimming line. Keep handles dry, clean and free from oil and grease. Always use a clean cloth when cleaning. 35. This appliance is double insulated to protect you from electrical shock. 36. Store the

28. Wear heavy, long pants, boots, gloves and a long sleeve shirt. Do NOT wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level. 29. Always release the hand grip trigger when cutting is delayed or when walking from one cutting location to another. To reduce the risk of elctrocution, keep all connections dry and of the ground. Do not touch the plug with wet hands. 2 OPERATING INSTRUCTIONS 10. Press on the head angle release button to change the angle

5/16" I.D.* 30 748-0298 Spacer .354" I.D. x.635" 63 718-0144 Grip O.D. x .510" Lg. 64 14427 Flap Bracket N 31 14341 - 497 Blade Guard N 65 711-0720 Hinge Pin N 32, 7W~0Jt9 •Z?# H 66 731-0532 Debris Deflector N *For faster service obtain standard nuts, bolts and washers locally. If these items cannot be obtained locally, order by part number and size as shown or parts list. The engine is not under warranty by the mower manufacturer. If repairs or service is needed on the engine, plea

No other express warranty or guaranty, whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product shall bind Troy-Bilt LLC. During the period of the Warranty, the exclusive remedy is repair or replacement of the product as set forth above. (Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.) The provisions as set forth in this Warranty provide