Оценок - 4, средний балл: 4 ( )

Производитель: Makita Размер: 936.14 kb Название файла: Язык инструкции:

If the nylon cord extends out too much or does not extend out enough, adjust the length of nylon cord while raising the spool slightly within the housing. 11) 80 mm 120 mm (3-118'' 4-314") ~ ~ 8. Set the spool in the housing so that the projections on the gear plate fit into the notches of the spool. (1I Notch 12) Projection 9. Align the small holes on the cover with the eyelets in the housing and install the cover over the housing so that the projections on the housing fit into the notches on the cover. (11 Hole (2)Cover (31Notch (41Projection (51Eyelet 10.Re-install the knob and tighten it securely by turning in the opposite direction of the arrow engraved on the knob. DAILY CHECKUP AND MAINTENANCE Cleaning of air cleaner If the air cleaner is clogged, remove it and clean If there is excessive dust or dirt adhering to the air cleaner, clean it every day A clogged air cleaner may make it difficult or impossible to start the engine or increase the engine rotational speed substantially Cleaning of cooling air passage Prior to operation, be sure to check the cooling air inlet (protection cover), gap between fuel tank and crankcase and clogging of the cylinder fins with dust. Clean them, if necessary. Remove the main cover and protection cover and clean the cooling air passage of dust or dirt inside. If operating the machine with the cooling air passage clogged with dust or dirt, the engine will not be cooled adequately and engine troubles will result. Checkup of spark plug The gap between the two electrodes of a spark plug is 0.6 to 0.7 mm (0.024" 0.028"). If the gap is ~ too wide or too narrow, adjust it. If the spark plug is clogged with carbon or fouled, clean it thoroughly or replace it. 0.6 mm 0.7 mm ~ (0.024" 0.028") ~ Supply of oil to gearcase Remove the hex bolt which plugs the grease hole in the gearcase. Apply grease (Shell albania No. 2 or equivalent) to the gearcase through the grease hole every 30 hours. (Genuine Makita grease may be purchased from your Makita dealer.) Cleaning of muffler exhaust port Check the muffler exhaust port (tail pipe) every 50 hours. If the exhaust port is clogged with carbon, remove it by scraping and tapping gently with a screwdriver or other adequate tools. (1) Grease hole (2)Gearcase STORAGE Storage When storing the machine for a long time, drain fuel from the fuel tank and carburetor, as follows Drain all fuel from the fuel tank Dispose of properly and in accordance with all local laws Remove the spark plug and add a few drops of oil into the spark plug hole Then, pull the starter gently to assure that an oil film covers the engine inside, then tighten the spark plug Clear or blow dirt or dust from the nylon cutting head and outside of engine, wipe them with a oil-immersed cloth and keep the machine at a place as dry as possible Be sure to wear appropriate eye and face protection (11 Drain fuel 121Humidity CHECKUP ITEMS FOR SAFE OPERATION Prior to operation, be sure to check the following items to assure safe operation of this machine No Check point Description C liec k u p - I 1 1 Apperarance 1 By visual inspection, check for damage, crdcks or wear I Common I 2 1 Bolts, nuts 1 Check for damdge, cracks, wear or loosening I 1) Check for damage, cracks or loosening protector is properly placed in contact with gearcase 1) Confirm that there are 110loose bolts Machine bodv I 5 I Handle 1 Confirm that handle dttdching bolts are tightened securely I 1) Are there any cracks or frdying, Hanging bdnd detach yourself from machine when pulling release belt’ 1) Does throttle lever work smoothly, Throttle lever 2) Can enqine rDm be adlusted between low and hiqh speeds, I 8 1 Stop switch 1 Does engine stop quickly and completely? Engine Muffler, 1) Clean carbon from muffler I 9 I muffler Cover 2) Check muffler cover for damage or looseningI 1 I i 1) Check damper bolt for secure tightening 2) Confirm that 3 holder case tightening screws are not loosened Makita Corporation 3-11-8, Sumiyoshi-cho, Anjo, Aichi 446 Japan PRINTED IN JAPAN 7+3 ' P+ 'In 1993-7 E 6219513601 ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: