Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
Plug heater into a standard AC outlet. Caution: Be sure that no other appliances are plugged into same circuit with heater as a circuit overload could occur. 2. Press ON/OFF button to activate heater. The red lights by POWER and TEMP SETTING buttons will turn on (B). 3. Press POWER button to select appropriate setting: LO for a x 3m), MED for a medium (approx. 12’x12’/3.8m x 3.8m), room (approx. 12’x 16’/3.8m x 5m). 4. Press TEMP SETTING button to MAX. Once desired room temperature lower temperature setting. Leave temperature control automatically cycle on and off to maintain your 5. This heater will continue to operate as long button is illuminated. Be sure to press ON/Note: Oil in unit is permanently sealed. You do not need to refill it. To set clock for current time of day: 1. Plug heater in. The digital clock AM until correct time is set. 2. Press FUNCTION button until 3. Set hour by pressing down ) or up ( ) arrow buttons. (If setting sure PM light is on.) Press flashing. 4 BDOH200.Pub179200RV2 5/18/05 9:11 AM Page 6 4. Set minutes by pressing the down ( ) or up ( ) arrow buttons. Press FUNCTION button again to set. Note: If heater is unplugged at any time, clock must be reset. To set timer: This heater has two automatic timers that enable it to turn on and off automatically during two time periods within 24 hours. You may set one or both timers depending on your preference. Once set, heater will operate only at the times chosen. To set TIMER I/ TIMER II: 1. Press ON/OFF button to turn heater on. The red lights by the POWER and TEMP SETTING buttons will turn on. 2. Press FUNCTION button (several times if needed) until both TIMER I or Timer II (if desired) and ON TIME lights start flashing. 3. Set hour and minutes by pressing down ( ) or up ( ) arrow buttons. Then press FUNCTION button again to set. 4. Press FUNCTION button until both TIMER I or Timer II (if desired) and OFF TIME lights start flashing. 5. Set hour by pressing the down ( ) or up ( ) arrow buttons until the hour is displayed. Then press FUNCTION button again. The minute LED will start flashing. Set minutes by pressing the down ( ) or up ( ) arrow buttons until minutes are displayed. Press FUNCTION button again to set. Once one or both timers are set, heater will cycle on and off continuously at the times you set until the timers are turned off, or power is turned off. When a timer is set, the green timer light will remain on. Then, as heater turns on during the set ON TIME chosen, the green light will turn red, indicating heater is on. The light will revert back to green when heater turns off after it reaches the set OFF TIME. To turn off the timers: You can turn off either or both timers. To turn off Timer I, set ON TIME and OFF TIME to 00:00. To turn off Timer II, set ON TIME and OFF TIME to 00:00. Special features and the (AST) Advanced Safety Technology™ system 1. This unit has a safety thermostat. If unit experiences excessive heat, thermostat off unit. If this happens turn power off immediately. Be sure that the fins are not blocked and nothing is restricting heater. Let it cool down, and wait 10 minutes before plugging it back in to operate. If unit fails to operate after 10 minutes, it may has internal damage and will need service or replacement. 2. A built-in tip-over switch will cut power if unit is accidentally knocked down in either direction. To reset, stand heater upright and wait a few seconds for it to begin operating again. Care and Cleaning This product contains no user serviceable parts. personnel. 1. Be sure heat control is in OFF position before Always unplug heater and allow it to cool thoroughly before attempting 2. Remove accumulated dust from heater You may use a cloth or sponge moistened with a mild detergent and water. Dry heater casing thoroughly soft, dry cloth before operating 3. Coil the cord around the 5 INSTRUCCIONES IMPORTANTES DE SEGURIDAD ADVERTENCIA: Para reducir el riesgo de incendio: . A fin de reducir el riesgo de incendio, cuando el calentador se encuentre enchufado, mantenga todo material combustible incluyendo los muebles, las almohadas, la ropa de cama, ropa, cortinas y papeles por lo menos a 0,9 m (3 pies) de distancia del frente, de los costados y de la parte trasera del calentador. . No coloque el calentador cerca de las camas; las almohadas o las cobijas podrian caerse de la cama e incendiarse al entrar en contacto con el calentador. . Siempre desconecte el calentador de la toma de corriente cuando este no se encuentre en funcionamiento. . Evite el uso de un cable de extension porque este se puede sobrecalentar y ocasionar el riesgo de un incendio. Si no tiene otra alternativa, utilice un cable de extension con capacidad minima de 14 AWG y de calificacion no menor de 1875 watts. PRECAUCION: Riesgo de incendio - No utilice este aparato sin antes haber instalado los rodillos. A fin de reducir el riesgo de un incendio, choque electrico o lesiones a las personas, cuando se utilizan aparatos e...
Эта инструкция также подходит к моделям:Электрообогреватели - BDOH200 (1.52 mb)