Оценок - 2, средний балл: 5
(
)
)
|
Фрагмент инструкции
Profundidad correcta: un diente debajo de la superficie de madera Battery Cap A B 8 Blade Lame Disco Inner clamp washer Rondelle de fixation externe Roldana de sujecion exterior Saw spindle Arbre de la scie Flecha de la sierra Blade clamping screw Vis de fixation de la lame Tornillo de sujecion del disco Outer clamp washer Rondelle de fixation externe Roldana de sujecion interior Direction of teeth Sens des dents Direccion de los dientes Kerf Plate and Screw Plaque de trait de scie et vis Placa indicadora de corte y tornillo For pocket cuts only Pour coupes en retrait seulement Solamente para cortes de bolsillo 10 7 Bevel adjustment knob Bouton de reglage pour coupes en biseau Perilla de ajuste de bisel Switch Handle Poignee de l’interrupteur Mango del interruptor Warning: When blade starts cutting, release retraction lever immediately Avertissement : Lorsque la lame commence a decouper, relacher immediatement le ressort de rappel. Advertencia: Cuando el disco inicie el corte, suelte inmediatamente la palanca del mecanismo retractil TightenSerrerApriete LoosenDesserrerAfloje 9A 9B Blade Wrench Cle de reglage de la lame Llave del disco Switch lock-off lever Levier de verrouillage en position «arret» Palanca de seguro de apagado Switch trigger Interrupteur a gachette Interruptor de gatillo 8 Blade Lame Disco Inner clamp washer Rondelle de fixation externe Roldana de sujecion exterior Saw spindle Arbre de la scie Flecha de la sierra Blade clamping screw Vis de fixation de la lame Tornillo de sujecion del disco Outer clamp washer Rondelle de fixation externe Roldana de sujecion interior Direction of teeth Sens des dents Direccion de los dientes Kerf Plate and Screw Plaque de trait de scie et vis Placa indicadora de corte y tornillo For pocket cuts only Pour coupes en retrait seulement Solamente para cortes de bolsillo 10 7 Bevel adjustment knob Bouton de reglage pour coupes en biseau Perilla de ajuste de bisel Switch Handle Poignee de l’interrupteur Mango del interruptor Warning: When blade starts cutting, release retraction lever immediately Avertissement : Lorsque la lame commence a decouper, relacher immediatement le ressort de rappel. Advertencia: Cuando el disco inicie el corte, suelte inmediatamente la palanca del mecanismo retractil TightenSerrerApriete LoosenDesserrerAfloje 9A 9B Blade Wrench Cle de reglage de la lame Llave del disco Switch lock-off lever Levier de verrouillage en position «arret» Palanca de seguro de apagado Switch trigger Interrupteur a gachette Interruptor de gatillo ASSEMBLY/ADJUSTMENT SET-UPWARNING: Always remove battery from tool before any of the following operations. ATTACHING AND REMOVING THE BLADE NOTE: The first time the blade bolt is removed from saw without a blade installed, it may be necessary to place the blade wrench on the bolt head and tap it sharply in the counter clockwise direction. Retract lower guard and assemble blade and clamp washers, as shown in Fig. 8. To prevent blade rotation while tightening the blade clamping screw, raise the lower guard and place the saw down on a piece of scrap wood as shown in Fig. 9A. The blade teeth will dig into the scrap wood and prevent rotation while you tighten the blade clamping screw. Tighten the blade clamping screw securely, using the wrench provided. Figure 9B illustrates an alternative method of loosening and tightening the blade by inserting a screwdriver through the hole in the blade to prevent it from moving. NOTE: The blade wrench is stored in the kerf plate as shown in Fig. 8. CUTTING DEPTH ADJUSTMENT Adjust depth of cut using depth adjustment lever. See (Figs. 5 & 6) for proper setting. Tighten lever securely. BEVEL ANGLE ADJUSTMENT Adjust bevel angle (Fig. 7) using bevel adjustment knob and bevel scale. Tighten knob securely. KERF PLATE ADJUSTMENT Adjust kerf plate (Fig. 8) to read zero when the bevel scale reads zero by loosening the kerf plate screw and sliding the plate as necessary. Align mark on kerf plate with drawn pencil line and advance blade into cut. The kerf plate has lines for zero bevel and 45 degree bevel cutting. OPERATING INSTRUCTIONS WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using tool. GENERAL CUTS (IMPORTANT: Read safety warnings and instructions. ) GUARD AGAINST KICKBACK With battery removed, follow all assembly, adjustment and set up instructions. Make sure lower guard operates. Select the proper blade for the material to be cut. • Measure and mark work for cutting. • Support and secure work properly (See Safety Rules and Instructions). • Use appropriate and required safety equipment (See Safety Rules). • Secure and maintain work area (See Safety Rules). • With battery inserted, make sure switch turns saw on and off. WARNING: It is important to support the work properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Fig. 3 illustrates typical hand support....
Эта инструкция также подходит к моделям:Лобзики и пилы - 609747-26 (502.77 kb)