Войти:
Скачали: 0   Размер: 13 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

To calibrate the blade tilt: 1. Disconnect the saw from the power source! 2. Move the blade tilt to 90. according to the gauge, and raise the main blade as high as it will go. 3. Place a machinist's square on the table surface and between the blade teeth. Inspect for gaps between the blade and the square. 4. If a gap exists at either the top or bottom of the square, loosen the set screw in the 90. tilt stop nut shown in Figure 83. 90. Tilt Stop Nut 45. Tilt Stop Nut Leadscrew Nut Figure 83. Blad

Скачали: 4   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

G0451 14" Sliding Table Saw -9 Additional Safety Instructions for Table Saws 1. SAFETY ACCESSORIES. Always use the blade guard and riving knife on all ''throughsawing'' operations. Through-sawing operations are those when the blade cuts com7. RIVING KNIFE ALIGNMENT. Only operate the saw if the riving knife is aligned with the main blade. pletely through the workpiece. 8. REACHING OVER SAW BLADE. Never reach behind or over the blade with either 2. 3. KICKBACK. Be familiar with kickback. Kickback

Скачали: 1   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

Except for details given in this insert, the content in the Model G0513X owner's manual is the same for both machines. Before operating your new machine, you MUST read and understand this insert and the entire Model G0513X manual to reduce the risk of injury from improper use or setup. If you have any further questions about this manual insert or the differences between the Model G0513X2 and the Model G0513X, contact our Technical Support at (570) 546-9663 or email techsupport@grizzlv. com. CO

Скачали: 0   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

#TR8129 PRINTED IN TAIWAN ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Скачали: 0   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

Use the shims that came with the scoring blade set (Figure 38) to stack the scoring blade to the same thickness as the main blade. Figure 38. Typical scoring blade with shims. 5. Install the blade set with the teeth facing the opposite direction as the main blade, then reinstall the arbor flange and the arbor nut. 6. Place a hex wrench in the hole in the arbor and use the arbor wrench to tighten the arbor nut as shown in Figure 39. Note: The arbor nut has right-hand threads and tightens by turni

Скачали: 0   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

Note: Get assistance positioning the tables and holding them in place while installing. Set Screws Mounting Screws Figure 20. Small extension wing attached. 4. Attach the support leg (Figure 21) to the large extension wing with the M10-1.5 x 45 hex bolt, lock washer, and flat washer. Figure 21. Support leg installed. 5. Check the table surfaces with a straightedge, as shown in Figure 22, to ensure that they are flush and even with each other. Figure 22. Checking with a straightedge. 6. Adjust th

Скачали: 1   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

#BL8591 PRINTED IN TAIWAN ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Скачали: 2   Размер: 12 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

#BL8591 PRINTED IN TAIWAN ..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................

Скачали: 0   Размер: 11 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

14 Operation.................................................................................................................................. 14 Grounding................................................................................................................................. 15 Extension Cords....................................................................................................................... 15 Phase Converter ..........................................................

Скачали: 1   Размер: 11 mb   Производитель: Grizzly  
Категория: Лобзики и пилы
@name

#EWTR7787 PRINTED IN TAIWAN ........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................





Категории