Войти:
Оценок - 5, средний балл: 3.6 ( )

Инструкция по эксплуатации Black & Decker, модель SKAT-02 M

Производитель: Black & Decker
Размер: 591.77 kb
Название файла:
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


6.8.5. Ensure that the machine has been cleaned, tested and maintained before starting to operate. 6.8.6. Check the safety devices, power cable and moving parts regularly. Don’t operate the machine before having replaced defective safety devices or faulty parts. 6.8.7. Never replace the saw blade before unplugging first. 6.8.8. Keep foreign materials away from the working area of the machine, keep away from the machine’s moving parts. IMPORTANT The safety data have been defined above. In order to prevent physical damage or damage to the equipment, please read the safety information carefully and keep the manual always in an easy accessible place. 15 Operating and Safety Instructions 7. OPERATION The miter saws PEGASUS / SKAT cut non-ferrous aluminum, PVC profiles and PVC materials. The operator adjusts (manually via knob) the cutting speed of the saw blade according to the material type to be cut. Inner and outer sharp edges of the carbide tipped circular saw blade ensures high quality clean cutting results. The cutting length can be precisely read and adjusted using the measuring tape fixed to the back fence. CAUTION! Start the machine only after proper clamping of the work piece to be cut. The machine is equipped with horizontal clamps. The clamping positions, either manual or pneumatic clamps, can be adjusted comfortably according to the material. At manual clamps the clamp shaft can be moved 50 mm. At pneumatic clamps the clamp piston can be moved 55 mm. The clamping cylinders have to be outside of the saw blade moving area. (See Illustration 6 and 7) IMPORTANT The air pressure of the machine (pneumatic model) has to balance 6-8 Bar (90-120 psi) pressure. Don’t operate the machine with an air pressure lower than 6 Bar. 7.1. ADJUSTING THE AIR PRESSURE OF PNEUMATIC CLAMPS 7.1.1. Pull the adjustment button of the conditioner upwards. a-Turning the adjustment button in clockwise direction increases the pressure b-Turning the adjustment button in counter clockwise direction decreases the pressure c-Once you read 6-8 Bar (90-120 psi)on the manometer, push the adjustment button of the conditioner down and lock it in that position. 16 Operating and Safety Instructions Pressure Adjustment Button Manometer Air Pressure and Water Discharge Screw OilDepotOilFillingTap Illustration 3 7.1.1. Place the material to be cut on the machine table, take the measure the cutting length using the measuring tape on the back fence, and clamp the work piece (pneumatically or manually). 7.1.2. Start to operate the saw blade by pressing the Start button. 7.1.4. Carry out the cutting operation by pressing down the cutting head holding the grip. 7.1.5. After cutting off the material, bring the cutting grip to its original position, press the Stop button. The saw blade will come to a full stop within 15 sec. 7.1.6. Release the clamps (manually or pneumatically) and take out the cut work piece. 7.1.7. The conditioner unit collects the water within the air system in a recepta...

Эта инструкция также подходит к моделям:
Лобзики и пилы - PEGASUS-02 M (591.77 kb)
Лобзики и пилы - PEGASUS-02 M (591.77 kb)
Лобзики и пилы - PEGASUS-02 M (591.77 kb)
Лобзики и пилы - PEGASUS-02 P (591.77 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории