Оценок - 4, средний балл: 4.8 ( )

Производитель: Ariens Размер: 826.18 kb Название файла: Язык инструкции:

Engine alternator will normally keep battery fully charged with a 3 to 5 minute start/run cycle. IMPORTANT: Use battery supplied only. DO NOT attempt to "jump start" mower. If battery discharges, use a 5 to 10 minute start/run cycle to recharge battery, or use a battery charger (a battery charger, kit number 71104300, is available from Ariens). An engine run time of at least 8 hours is required to charge a fully discharged battery. To charge with Ariens battery charger, connect charger plug to mating plug on battery (not engine) and plug charger into 120 volt Alternating Current (AC) outlet. Charge for 12 to 36 hours (battery may be charged for up to 56 hours with no harmful effect). 5 - 31 SECTION 6 - MOWER DECK SECTION 6 - MOWER DECK 6. Bearing Retainer 7. Center Baffle 8. Traction Drive Pulley 9. Blade Adapter 1 2 3 4 5 6 7 8 9 3 1. Drive Belt 2. Drive Disk 3. Ball Bearing 4. Washer 5. Spindle Figure 18 6.1 BLADE BRAKE/CLUTCH REMOVAL Remove mower blade. Squeeze brake/clutch bail against handlebar and insert cotter pin into open hole of actuating rod. Remove 3/8-24x2-1/2" cap screw that retains brake, blade, clutch (BBC) leaf spring and leaf spring from shaft. Remove BBC flywheel by securing flywheel with BBC wrench (P/N 000239). Remove flywheel and cotter pin securing actuator rod to brake actuator. Remove three nuts and remove brake actuator from unit. Inspect parts for wear and or damage, replace as necessary. Assemble in reverse order. NOTE: When attaching actuator rod to brake actuator, brake actuator is to be rotated all the way up so proper hole is aligned. On models with key, position key in crankshaft. Slide flywheel onto crankshaft and BBC leaf spring onto flywheel stub shaft. IMPORTANT: Install 3/8-24x2-1/2" Gr. 5 cap screw and lockwasher to secure. Torque to 30 ft-lbs (40.6 Nm) using BBC wrench to hold leaf spring and flywheel. Secure mower blade with two 3/8-24x1-1/4" Gr. 5 cap screws with lockwashers, torque to 25-30 ft-lbs (33.8-40.6 Nm). Check idler for free rotation of pulley and movement of pivot. Replace drive belt in reverse order being sure that belt seats in pulley grooves with idler positioned on back (flat) side of belt. Brake Engaged Blade Engaged Figure 19 6 - 32 1. Blade 4. Flywheel 1 2 3 4 5 6 1. Blade 4. Flywheel 1 2 3 4 5 6 5. Brake Actuator Washer & Flat Washer 6. Ramp Assembly 3. Leaf Spring Figure 20 6.2 DRIVE BELT REPLACEMENT CAUTION: Use sturdy gloves or padding to protect hands when working with mower blades. NOTE: On BBC model blade brake/clutch assembly must be removed to change belt. Place right rear adjustment lever in first notch and left rear height adjustment lever in third notch. This provides clearance between friction wheel and drive disk. Remove belt from idler, drive disk and engine pulley. Remove belt through opening under mower pan. Inspect parts for wear and or damage, replace as necessary. Assemble in reverse order. NOTE: Be sure to return wheel height adjustment levers to original position. 6.3 IDLER REMOVAL Remove mower blade, hub, and center baffle. Refer to Mower Blade Section of this manual. Remove idler spring. Loosen hardware securing idler arm to mower pan, and remove cap screw securing idler to idler arm. Inspect parts for wear and or damage, replace as necessary. Assemble in reverse order. Figure 21 1. Two-Way Lock Nut 2. Idler 3. Extension Spring 4. Center Lock Nut 5. Washer 6. Idler Arm 7. Flange Bushing 8. Tension Spring 9. Spacer Configuration 1 1 2 3 4 5 6 7 1 2 9 7 8 Configuration 2 6.4 WHEELS AND ADJUSTERS Regularly check wheels and adjusters for wear. Replace wheels when they become excessively worn. Adjusters should be cleaned and fasteners checked for tightness. Check the front wheels for bushing wear. Replace as needed. 6 - 33 Figure 22 Friction Drive 1. Height Adjustment Lever 2. Spacer Tube 3. Ball Bearing 4. Handlebar Mounting Bracket 5. Rear Quadrant 6. Front Height Adjustment Lever 7. Front Quadrant 8. Adjuster Bracket 9. De-Thatcher Retainer 10.Flat Washer PM0065 1 2 3 4 5 6 7 8 9 10 Figure 22 Friction Drive 1. Height Adjustment Lever 2. Spacer Tube 3. Ball Bearing 4. Handlebar Mounting Bracket 5. Rear Quadrant 6. Front Height Adjustment Lever 7. Front Quadrant 8. Adjuster Bracket 9. De-Thatcher Retainer 10.Flat Washer PM0065 1 2 3 4 5 6 7 8 9 10 4 6 - 35 Figure 23 Gear Drive 1. Washer 2. Inner Wheel Cover 3. Ratchet Pinion 4. Ball Bearing 5. Height Adjuster 6. Rear Quadrant 7. Height Adjustment Lever 8. Handlebar Mounting Bracket 9. Key Ratchet 10.Tuff Torque Transmission 11.Front Quadrant 12.Washer 13.Spacer 14.De-Thatcher Retainer 15.Adjuster Bracket PM0360 1 2 3 4 5 6 7 8 9 10 11 12 7 15 14 13 Figure 24 1. Kickout Ring 2. Sleeve Bushing 3. Clevis Pin 4. Mount Arm 5. Axle Tab 6. Flange Bushing 7. Wheel Yoke 8. Lube Fitting 1 2 3 4 2 5 6 7 8 PM0071 Figure 24 1. Kickout Ring 2. Sleeve Bushing 3. Clevis Pin 4. Mount Arm 5. Axle Tab 6. Flange Bushing 7. Wheel Yoke 8. Lube Fitting 1 2 3 4 2 5 6 7 8 PM0071 6 SECTION 7 - HANDLEBARS...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: