Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
Don’t operate the machine with an air pressure lower than 6 Bar. 7.1. ADJUSTING THE AIR PRESSURE OF PNEUMATIC CLAMPS 7.1.1. Pull the adjustment button of the conditioner upwards. a-Turning the adjustment button in clockwise direction increases the pressure b-Turning the adjustment button in counter clockwise direction decreases the pressure c-Once you read 6-8 Bar (90-120 psi)on the manometer, push the adjustment button of the conditioner down and lock it in that position. 16 Operating and Safety Instructions Pressure Adjustment Button Manometer Air Pressure and Water Discharge Screw OilDepotOilFillingTap Illustration 3 7.1.1. Place the material to be cut on the machine table, take the measure the cutting length using the measuring tape on the back fence, and clamp the work piece (pneumatically or manually). 7.1.2. Start to operate the saw blade by pressing the Start button. 7.1.4. Carry out the cutting operation by pressing down the cutting head holding the grip. 7.1.5. After cutting off the material, bring the cutting grip to its original position, press the Stop button. The saw blade will come to a full stop within 15 sec. 7.1.6. Release the clamps (manually or pneumatically) and take out the cut work piece. 7.1.7. The conditioner unit collects the water within the air system in a receptacle in order to prevent damage to the pneumatic system components. Discharge this water periodically (at the end of the working day) by pressing or opening the button under the conditioner. 7.1.7. The manufacturer recommends to use the following oils with the conditioner: TELLUS C 10 / BP ENERGOL HLP 10/ MOBIL DTE LIGHT / PETROL OFISI SPINDURA 10. Don’t operate the saw while it touches the work piece. The saw must be operated only when the head is in the top position. 17 Operating and Safety Instructions 7.2. MITER CUT: 7.2.1. Press the saw blade down until it touches the cutting slot of the table. 7.2.2. Pull out the snap pin from its slot. (See Illustration 4) 7.2.3. Pull the table locking Bar to the left to unlock. (See Illustration 4) 7.2.3. Adjust the desired angle by turning the cutting head to the right or left. (See Illustration 5) 7.2.4. The cutting angles 15°-22.5°-30°-45° are fixed by releasing the snap. Pull the table locking handle to the right and fix the table (See Illustration 5) TableLockingHandle(Locked) Snap Pin TableLockingHandle(Unlocked) Illustration 4 Illustration 5 7.2.5. At intermediate angles (5°-10°-15°-35°-40° …) lock the table by pulling the table locking handle to the right. No Stock No / Part Name Qty 30 141-112 BLADE SHAFT 1 31 112-019 BLADE SHAFT PULLEY 1 47 141-094 OUTER NUT WASHER 1 48 141-092 BLADE WASHER 1 49 114-018 BLADE INNER NUT WASHER 1 50 201-003 350 mm SAW BLADE 1 50 201-004 400 mm SAW BLADE 1 52 111-166 PEGASUS HEAD 1 52 111-243 SKAT I HEAD 1 54 141-093 WASHER 30x8x7 1 55 172-025 M8x16 HEXAG. SCREW 1 18 ...
Эта инструкция также подходит к моделям:Лобзики и пилы - PEGASUS-02 M (591.77 kb)
Лобзики и пилы - PEGASUS-02 M (591.77 kb)
Лобзики и пилы - PEGASUS-02 M (591.77 kb)
Лобзики и пилы - PEGASUS-02 P (591.77 kb)