Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
There is no need to run the batteries down completely before recharging. Normal usage is the best method of discharging and recharging the batteries. Maintenance Stage The trickle charge feature of the charger allows the battery pack to remain in the charger and ready for use. With the charger connected to standard household current, the red charging indicator light will glow constantly. The charger will keep the battery pack fully charged. A battery pack will slowly lose its charge when kept out of the charger. Removing & Refitting the Blade WARNING: Always ensure that the battery is removed from the tool when changing blades. Removing the Blade (Figure 3) Ensure blade has cooled after use. Press and hold the rear of the black blade release button fully, hold the back of the blade and rotate it 90 degrees in a downward direction. Slide the blade sideways off the location pin and remove from the saw. Fitting a Blade (Figure 4,5) Place the blade, with the tooth protector fitted, over the location pin. The blade teeth should be facing the handle. Rotate the blade through 90° until it is fully located in the slot and the location pin is in the locked position.To ensure the blade is securely fitted try to remove without pressing the blade release button. Remove the tooth protector, your saw is now ready for use. NOTE: If you are unable to fit the blade, check to see if the slot in the location pin is straight up and down. If it is not, keep the blade release button depressed and use a flat bladed screwdriver to turn the location pin into the correct position as shown in Figure 5. Operating Instructions WARNING: When cutting, hold saw firmly with two hands as shown in Figure 7. Variable Speed Trigger Switch (Figure 6) Your saw is equipped with a variable speed trigger switch that allows you greater control over start of cut, rate of cut and breakthrough of cut. To switch your saw on, slide lock-off button (1) and squeeze the on/off variable speed trigger switch (2). To switch off, release the trigger, the unit will automatically lock-off. Cutting With Tool (Figure 7) Hold tool with two hands as shown in Figure 7. To obtain the best results from your saw, use the same backward and forward movement you would employ with a traditional hand saw. This will enable a quicker cleaner cut. Cutting Metal Your saw can be used for cutting light gauge ferrous and non-ferrous metals such as copper, brass, aluminum, etc. with the specified blade. See recommended materials. It is advisable when cutting thin sheet to clamp a backing sheet of soft wood or plywood to the work as this will enable you to obtain a cleaner cut. Both metal and wood backing are sawn together. Do not force the cutting blade into the metal as this will reduce the life of the blade and possibly damage the motor. Cutting thin metal will take longer than cutting even a relatively thick piece of wood, so do not be tempted to speed up the operation by forcing the saw. Only use the metal cutting blade for this purpose. Recommended Materials Capacity Large Capacity Blade Soft wood Up to 4" x 4" Plastic soil pipe Up to 4-7/8" Curve Cutting Blade Worktop Up to 2" Metal Cutting Blade Ferrous/non-ferrous metals Up to 1/8" thick Maintenance Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. The RBRC™ Seal The RBRC™ (Rechargeable Battery Recycling Corporation) Seal on the nickel-cadmium battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to place spent nickel- cadmium batteries in the trash or municipal solid waste stream and the RBRC program provides an environmentally conscious alternative. RBRC in cooperation with Black & Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent nickel- cadmium batteries. Help protect our environment and conserve natural resources by returning the spent nickel-cadmium battery to an authorized Black & Decker service center or to your local retailer for recycling. You may also contact your local recycling center for information on where to drop off the spent battery, or call 1-800-8-BATTERY. Accessories Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO (544-6986). WARNING: The use of any accessory not recommended for use with this tool could be hazardous. Service Information All Black & Decker Service Centers are staffed with trained person...
Эта инструкция также подходит к моделям:Лобзики и пилы - 5105119-02 (299.31 kb)
Лобзики и пилы - BDPHS1800 (299.31 kb)