Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
We recommend that you always wear a dust mask when operating this saw. • Wear gloves when handling saw blades and rough materials. • Saw blades shall be carried in a holder wherever possible. • Select saw blades in relation to the material being cut. • Use correctly sharpened saw blades and observe the maximum speed marked on the blade. • Take additional care when trenching (slotting). • The mitre saw can be safely carried by the carrying handle but only once it has been removed from the mains power and secured in the locked down position. • Ensure that the arm is properly secure when bevelling. • Keep the floor area around the machine level, well maintained and free of loose materials. • Ensure that you are trained in the use, adjustment and operation of the machine. • Do not remove any cut-offs from the cutting area until the guard is fully locked in placed and the blade has come to rest. • When cutting long pieces which extend well over the table width, ensure that the ends are adequately supported at the same height as the saw table top. Supports should be positioned in such a way to ensure that the workpiece does not fall to the ground once the cut has been made. A number of supports at regular intervals may be required if the workpiece is extremely long. Wear goggles Wear earmuffs Wear a breathing mask Accessories The GMC DB250SMS / DB305SMS Double Bevel Slide Compound Mitre Saw is supplied with the following accessories as standard: • Saw blade (fitted) • Workpiece clamp • 6mm Hex key • Side bars x 2 • Stabiliser Bar • Dust bag • Instruction manual 7 Know your product Before using the saw, familiarise yourself with all the operating features and safety requirements. 24 36 1. Laser light assembly 2. Laser light on/off switch 3. Laser cover 4. Laser pitch control 5. Saw arm 6. Release knob 7. Operating handle 8. Carrying handle 9. Upper fixed blade guard 10. Clamp assembly 11. Clamp assembly lock (x2) 12. Rotating blade guard 13. Guard retraction arm 14. Blade bolt cover 15. Dust bag 16. Bevel lock 17. Bevel scale 18. 0° Bevel adjuster 19. Fence 20. 6mm Hex key 21. Mitre table 22. Mitre scale 23. Table insert (kerf plate) 24. Switch trigger 25. Mitre lock 26. Spindle lock 27. Dust extraction port 28. Slide bars 29. Slide lock 30. Trenching depth adjustment screw 31. Trenching stop 32. Trenching depth lock nut 33. 45° Bevel adjustment screw (left) 34. 45° Bevel adjustment screw (right) 35. 0° Bevel adjustment screw 36. Release latch 37. Side support bars (x2) 38. Side support bar location holes (2 sets) 39. Side support bar locking screws 40. Stabiliser bar 9 13 12 14 30 32 1 31 19 3 39 10 21 11 23 37 17 22 25 38 26 2 8 27 29 6 28 20 5 16 4 15 18 35 34 33 40 Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. 1. Remove all loose parts from the carton. 2. Remove the packing materials from around the saw. 3. Using the carrying handle (8) carefully lift the saw from the carton and place it on a level work surface. 4. The saw has been shipped with the saw arm locked in the down position. To release the saw arm, push down on the top of the saw arm, pull on the release knob (6), rotate it 45° and let go, slowly raise the saw arm. WARNING. Do not lift the saw whilst holding on to the guards. Use the carrying handle (8). Transportation Lift the mitre saw only when the saw arm is locked in the down position, the saw is switched off and the plug is removed from the power point. Only lift the saw by the carrying handle (8) or outer castings (Fig. A). Do not lift the saw using the guard or operating handle (7). Bench mounting The saw base has holes in each corner to facilitate bench mounting (Fig. B). 1. Mount the saw to a level, horizontal bench or work table using bolts (not supplied) and fix the saw to the bench using 4 bolts. 2. If desired, you can mount the saw to a piece of 13mm or thicker plywood which can then be clamped to your work support or moved to other job sites and re-clamped. CAUTION. Make sure that the mounting surface is not warped as an uneven surface can cause binding and inaccurate sawing. Stabiliser bar When the saw is not fitted to a bench, always fit the stabiliser bar (40) into the holes at the rear of the saw base (Fig. C). The stabiliser helps prevent the saw from tipping backwards when the slide action is used. Release knob The release knob (6) is provided for holding the cutting head down whilst transporting or storing the mitre saw (Fig. D). The saw must never be used with the release knob locking the head down. Slide lock When tightened, the slide lock (29) prevents the saw head from sliding. Tighten the slide lock during transportation (Fig. E). C D A E B Mitre table lock The mitre table lock (25) is used to lock the table at the de...
Эта инструкция также подходит к моделям:Лобзики и пилы - DB305SMS (12.2 mb)
Лобзики и пилы - LJS750CF (12.2 mb)