Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
The Exit and Run Program button verifies that all of the setup information has been saved to the EEPROM and displays the main page that has been programmed into your system. The remaining buttons on the MAIN MENU open other menus which are discussed in subsequent paragraphs. MAIN MENU Calibration Menu CALIBRATION MENU Touch Perform Calibration. The message “Touch Upper Left” appears centered on the panel with a cross hair in the upper left corner. Touch the center of the cross hair in the corner of the screen to initiate calibration. Another message, “Touch Upper Right”, appears with a cross hair in the correct corner. Touch the center of the cross hair in the corner of the screen. A final message, “Touch Lower Right”, appears with a cross hair in the correct corner. Touch the center of the cross hair in the corner of the screen to conclude calibration and return to the CALIBRATION MENU. NOTE: When touching the screen during calibration be as accurate as possible. Use the tip of a capped pen or the eraser end of a pencil. To cancel calibration and return to the CALIBRATION MENU without saving calibration data, create a calibration error by touching the screen in the same spot three times. Setup Menu To obtain the SETUP MENU press the Setup button from the MAIN MENU. The SETUP MENU offers a series of buttons which open additional menus and displays and are detailed in subsequent paragraphs. The SETUP MENU also provides Down/Up buttons to control Screen Brightness, Key Backlight and Standby Timeout. The Hardkey Test Results indicators will light when each respective button is pushed on the touchpanel. After setup parameters have been selected, select the Return button to return to the MAIN MENU. NOTE: For convenience the current CRESNET ID setting is displayed in the upper left corner. NOTE: All touchpanel settings are automatically saved in non-volatile memory. SETUP MENU Interface Menu The touchpanel communicates with a control system to activate commands or to display feedback from components within the system. The communication interface must be correctly specified or communication will not occur. To set communication parameters select the Interface button located on the SETUP MENU and display the INTERFACE MENU, shown after this paragraph. The Cresnet network identity number (CRESNET ID also known as the Net ID) is displayed on the INTERFACE MENU. Net ID is the two-digit hexadecimal number. The hexadecimal number can range from 03 to FE and must correspond to the Net ID set in the SIMPL Windows program of the Cresnet system. Matching IDs between touchpanel and SIMPL Windows program is required if data is to be successfully transferred. Net ID for the TPS-12B/W, TPS-15B/W & TPS-17B/W is factory set to 03. No two devices in the same system can have the same Net ID. INTERFACE MENU Two buttons adjacent to the hexadecimal display, DOWN and UP, decrease and increase the Net ID by one, respectively. The four buttons at the bottom define how the RS-232 port can be used; as a console port (i.e. loading touchpanel projects and firmware), a touch output port (communication of touch coordinates to an external device), a mouse input port (allows a mouse to control the touchpanel) and an external touch input (allows another device to control the touchpanel). The Ethernet Enable and Disable buttons determine the status of the touchpanel’s Ethernet communications. NOTE: The TPS-12B/W, TPS-15B/W & TPS-17B/W do not support a wireless Ethernet connection. There may be Ethernet devices (i.e. a control system) on the network that communicates with the touchpanel via CIP (Cresnet Internet Protocol). Two buttons located on the INTERFACE MENU determine if the touchpanel is capable of this type of communication. Select Enable to permit this protocol recognition and Disable to prohibit any CIP connection. CIP must be enabled for the touchpanel to communicate with other Crestron Ethernet devices. Select the Save and Return button located on the INTERFACE MENU to save changes and return to the SETUP MENU. Ethernet Setup Menu Selection of the Ethernet button from the SETUP MENU displays the ETHERNET SETUP MENU. This menu provides buttons for Ethernet Status Test (for details such as the IP Address, Subnet Mask, Default Router, IP Table, etc.), DHCP Enable/Disable and Static IP Options. Each of the Static IP Options has its own menu, as shown in the illustrations on the following pages. The enable/disable Ethernet feature is provided on the INTERFACE MENU. Ethernet settings are made through Crestron Toolbox. Refer to the TCP/IP Communications section of “Establishing Communication”, which starts on page 47 for additional Ethernet setup details. ETHERNET SETUP MENU ETHERNET STATIC IP SETTINGS ETHERNET DNS SETTINGS ETHERNET WINS SETTINGS Selection of the DHCP Enable button from the ETHERNET SETUP MENU displays the DHCP options Renew and Release. ETHERNET SETUP MENU (DHCP ENABLED) RS-232 Menu The touchpanel allows for one of four RS-232...
Эта инструкция также подходит к моделям:Кпк - TPS-12B/W (2.86 mb)
Кпк - TPS-17B/W (2.86 mb)