Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
It is very important to follow the assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed correctly, the treadmill could have frame parts that are not tightened and will seem loose and may cause irritating noises. There should be no side-to-side play in the console masts or any forward and back play in the console assembly or handlebars. If there is any play in these areas, the treadmill has not been properly assembled. To prevent damage to the treadmill, the assembly instructions must be reviewed and corrective actions should be taken. UNPACKING Place the treadmill carton on a level flat surface. It is recommended that you place a protective covering on your floor. Take CAUTION when handling and transporting this unit. Never open box when it is on its side. Once the banding straps have been removed, do not lift or transport this unit unless it is fully assembled and in the upright folded position, with the lock latch secure. Unpack the unit where it will be used. The enclosed treadmill is equipped with high-pressure shocks and may spring open if mishandled. Never grab hold of any portion of the incline frame and attempt to lift or move the treadmill. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN INJURY! Before proceeding, find your treadmill’s serial number and model name located to the left of the on/off power switch and power cord and enter it in the space provided below. enter your serial number and model name in the boxes below: SERIAL NUMBER : MODEL NAME: * Refer to the serial number and model name when calling for service. * Also enter this serial number on your Warranty Card. WARNING 1.3TASSEMBLY PARTS1 Power Cord1 Safety Key2 Water Bottle Holders3 Hardware BagsLeft and right outer Console Mast Covers1 Console AssemblyTOOLS(INCLUDED) 5mm Allen WrenchFlat Wrench6mm T-WrenchNOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your treadmill, to prevent loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before completely tightening any ONE bolt. If you have questions or if there are any missing parts, contact Customer Tech Support. Contact information is located on the back panel of this manual. For a complete exploded diagram, visit us at BOTTLE HOLDERCONSOLE MASTTRANSPORT WHEELDISPLAY CONSOLE MAST COVERSAFETY KEY PLACEMENTCIRCUIT BREAKERON/OFF SWITCHPOWER CORDCONSOLETOUCH PADGRIP PULSE HANDLE BARSMOTOR COVERSIDE RAILROLLER END CAPRUNNING BELT REAR ROLLERADJUSTMENT BOLTS TIMEDISTANCECALORIESPULSEINCLINESPEED1MPH2MPH3MPH4MPH5MPH6MPH7MPH8MPH9MPH10MPHPRESSENTERTOSETSPEEDMAGNETIC KEY1.3TINCLINESPEEDINCLINE% SPEEDMPHSTOPHOLD TO RESETSTARTQUICKSTARTENTERCHANGE DISPLAY1234567891012345678910 PRE-ASSEMBLY WARNING DO NOT CUT STRAPS UNTIL STEP 1-E!* Disassemble box and remove the cardboard packaging that is not beneath the treadmill. Do not attempt to lift the treadmill at this time. Remove plastic wrap from console masts. Open HARDWARE BAG 1. Lift left console mast into upright position. Be sure to hold the console mast firmly, as it will not stay in the upright position on it’s own. Move left side linkage arm into position. Insert bolt (A) and tighten. Repeat on the right side. Now cut the banding straps and remove remaining packaging material.* ASSEMBLY STEP 1 BOLT (A) LOWERLINKAGEARMBOLT (B) NUT (C) LINK ARM COVER TIMEDISTANCECALORIESPULSEINCLINESPEED1MPH2MPH3MPH4MPH5MPH6MPH7MPH8MPH9MPH10MPHPRESSENTERTO SETSPEEDMAGNETIC KEY1.3TINCLINESPEEDINCLINE% SPEEDMPHSTOPHOLD TO RESETSTARTQUICK STARTENTERCHANGE DISPLAY1234567891012345678910 HARDWARE BAG 1 CONTENTS : A B C D E BOLT (A) 45 mmQty: 2 ........................ * Note: If the straps have been removed before completing step 1-D and the linkage arms cannot be aligned, refer to the troubleshooting section (page 35) in order to restore the treadmill to its proper position. ASSEMBLY STEP 2 HARDWARE BAG 2 CONTENTS : A B C D Open HARDWARE BAG 2. Lift CONSOLE (as shown) to lock it into place. Insert BOLT (B) through CONSOLE MAST and secure using NUT (C). Repeat on other side. Note: Do not pinch the wires. .................................................................................... BOLT (A) LOWERLINKAGEARMBOLT (B) NUT (C) LINK ARM COVER TIMEDISTANCECALORIESPULSEINCLINESPEED1MPH2MPH3MPH4MPH5MPH6MPH7MPH8MPH9MPH10MPHPRESSENTERTO SETSPEEDMAGNETIC KEY1.3TINCLINESPEEDINCLINE% SPEEDMPHSTOPHOLD TO RESETSTARTQUICK STARTENTERCHANGE DISPLAY1234567891012345678910 ASSEMBLY STEP 3 HARDWARE BAG 3 CONTENTS : BOLT (D) CONSOLE MAST COVER BOLT (D) 16 mm Qty: 6 Open HARDWARE BAG 3. Place CONSOLE MAST COVERS over CONSOLE MASTS as shown. Attach CONSOLE MAST COVERS using 6 BOLTS (D). Place WATER BOTTLE HOLDERS and SAFETY KEY into the correct positions. It is now safe to plug in your treadmill. A B C D WATERBOTTLEHOLDERSAFETY KEY YOU’RE FINISHED! INTRODUCTION INTRODUCTION...