Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Failure to do so could result in a loss of warranty. • A damaged supply cord should be replaced by the manufacturer, its service agent or a qualified person in order to avoid a hazard. WARNING • Never operate this appliance if it has a damaged cord or plug. Do not lead the cord over sharp edges. • Don’t lift or move by pushing the air conditioner at the rear, but always at the front side. 3 PARTS PARTS Air outlet Control panel Carrying handle Caster wheels Filter holder Air inlet Exhaust air outlet Cable storage Water stopper / drainage point Water container Exhaust hose Remote control Air filter Controls ON/OFF UP DOWN MODE TIMER SLEEP FAN SPEED Telescopic slide bar Slide bar connector Display COOLING FAN HEAT HOURS:MINUTES TEMPERATURE 44 INSTALLATION INSTALLATION WARNING! Before using the air conditioner it should be left in an upright position for at least 2 hours. This unit can easily be moved from one room to another. In doing so keep this in mind: – Ensure that the unit is positioned upright, on a level surface and 50 cm away from obstacles. – To place the loose filters in the filter holder. • Take the filter holder out of the air conditioner • Release the filter fixer and place the active carbon filter (black) and 3M Filtrete™ filter (white), where included, in the filter holder. • Place the filter fixer back in the holder. • Place the filter holder back in the air conditioner. – Do not operate the unit inside the bathroom, shower, or in any other very humid environment. – Connect the hose to the unit by turning it clockwise (at least 5 turns). – Similarly, connect the hose to the slide bar connector as far as possible. – Place the telescopic slide bar in the open window or door and adjust the length to fill as much open space as possible. – Put the slide bar connector in the opening in the telescopic slide bar. – Close the window or door as much as possible to prevent outside air entering the room. – Ensure that the slide bar connector has a free flow outside. .................... Important The flexible exhaust hose can be extended from 500 to 1500 mm for mounting. This length has been designed especially according to the specifications of the air conditioner. Do not use an extension or exchange for a different hose as that may lead to malfunctioning. The exhaust air must flow freely, any blockage can lead to overheating of the air conditioner. Take care to prevent any sharp bow or bend in the exhaust. OPERATION ON/OFF Press to switch the unit on or off. A buzzer will beep, and the LCD will display 12:00 o’clock as default. Setting the clock Press the button for 3 seconds to set the clock. The 2 left digits of the 4 digits on the LCD-display will flash. Press or to adjust the hour. Press momentarily, the 2 right digits of the 4 digits will flash. Press or to adjust the minutes of the clock. Press the button for 3 seconds again to activate the clock. 5 Setting the temperature If you want to change the set temperature press or to set the temperature. The 2 digit display will indicate the set temperature. Note: Reaching the set temperature depends on the room and outdoor climatic conditions. Mode switch Press the button successively until the icon representing the desired mode is appearing (=> Cool => Fan => Heat => etc). On the LCD-display you will see: Cooling Fan only Heat Each time the unit starts, it starts operating in cool mode with a set temperature of 22°C. The fan speed will be selected automatically. Heat mode is only available on EH models. Fan speed If you prefer a constant fan speed instead of the auto fan speed, press the button successively; the fan icon on the LCD-display will rotate accordingly. • Fast - for the turbo speed • Normal - for the medium speed • Slow - for the slow speed • Alternating - for the auto fan speed (in the cooling mode only!) Heat EH models feature a 1650 W electric heater that can heat a room on cooler days. With the mode switch select , set the desired temperature and the unit will heat until this temperature is reached. Fan speed is selected automatically. Do not place the unit near anything that could catch fire or be scorched. Do not obstruct the air outlet. The heat function will operate with or without the hose attached. Timer For all of the following TIMER programming, proceed firstly with these standard steps: • Press the • Press or • Press the • Press or button briefly; the 2 left digits of the 4 digits on the LCD display are flashing. to adjust the hour. button briefly again, the 2 right digits of the 4 digits are flashing. to adjust the minutes of the clock in intervals of 5 minutes. The timer is set. After 10 seconds the time display returns. Programming the timer for ON - when the unit is OFF. • Perform the standard steps as described above. The circular time scale will be on between the ON programmed times until 24:00. The flashing bar on the time scale indicates the real time and moves a segment ahead every 30 minutes until it reaches the ON time...
Эта инструкция также подходит к моделям:Кондиционеры - 12000E (804.93 kb)
Кондиционеры - 15000E (804.93 kb)