Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Компьютеры - HP ProLiant WS460c Gen8 Workstation (691.53 kb)
Компьютеры - HP ProLiant WS460c Gen8 Workstation (728.29 kb)
Компьютеры - HP ProLiant WS460c Gen8 Workstation (686.99 kb)
Компьютеры - HP ProLiant WS460c Gen8 Workstation (731.92 kb)
Фрагмент инструкции
Solution Quick Start Guide | HP Graphics Server Blade Microsoft RemoteFX vGPU Quick Start
o
User mode — production RFX mode. In this mode the add-on card is enabled and the embedded Matrox
card is disabled.
In this mode it is not possible to reach the iLO console through iLO, the OA, or front I/O dongle.
You must enable the remote RDP console for systems management.
If unfamiliar with these system and video modes, please read Appendix A before continuing.
Windows Server 2012 R2 running on Gen9 servers can use both the embedded GPU and an add-in GPU at the same
time when running in UEFI mode. It is no longer necessary to disable the embedded GPU running in production.
In Windows Server 2012, there is a known issue during the Windows boot process where it will hang on a screen
stating “Getting Devices Ready.” This issue only happens on Server 2012 (not 2012 R2). To work around this,
disconnect the GPU, install the server OS fully, and patch it with all Windows updates. Once the updates are
installed you can reconnect the GPU and continue with the installation. Another workaround is to use 2012 R2.
On a Graphics Server Blade with an NVIDIA K1 or K2 you must run system BIOS version 11/15/13 or later.
Documentation on this issue can be found at the following URL:
http://h20564.www2.hp.com/portal/site/hpsc/public/kb/docDisplay/?docId=emr_na-c04013756
Install and Configure RemoteFX vGPU on a Graphics Server Blade
Initial Setup Procedure for WS460c Gen8 Blades
1. Update the WS460c Graphics Server Blade with the latest HP SPP firmware by booting to the SPP DVD.
You can obtain the latest SPP from the following page: http://www.hp.com/go/spp
2. Set up the system BIOS for installation.
a. Boot to the HP RBSU (BIOS configuration utility) by pressing F9 during boot
b. Go to and select System Default Options Restore Default Options and select to restore
c. After resetting boot back into HP RBSU (BIOS configuration utility) by pressing F9 during boot.
d. Set the video mode to Setup.
i. Select System Options and press ENTER.
ii. Select Remote Console Mode and press ENTER.
iii. Select Setup mode and press ENTER.
e. Set the blade to static high performance mode.
i. Select Power Management Options HP Power Profile.
ii. Select Maximum performance and press ENTER.
3. If installing Server 2012 (not 2012 R2), due to issues noted above, it is recommended that you disconnect the GPU
until Windows is installed and patched with all Windows updates. If installing 2012 R2, ignore this step.
4. Install Server 2012 R2.
5. Update the WS460c Graphics Server Blade with the drivers and software using HP SPP. You can obtain the latest
SPP from the following page: http://www.hp.com/go/spp
6. If you disconnected your GPU while installing Server 2012, reconnect it now.
7. Download the latest test NVIDIA Server 2012 driver from the HP or NVIDIA web page:
http://www8.hp.com/us/en/drivers.html
8. Install the NVIDIA driver.
9. Reboot the server.
10. Go to the device manager and under “Display Adapters” you should see the new NVIDA card listed.
Important note – In Setup mode is it normal for the NIVIDA card to be “banged” out with a yellow exclamation point
next to it. Windows does not support two different types of video cards.
4
...