Оценок - 4, средний балл: 4 ( )

Производитель: Topcon Размер: 2.58 mb Название файла: Язык инструкции:

[HOLD] is to fix vertical angle to the prism position even updown the telescope position, and [FREE] is to gear vertical angle to the updown of telescope movement. In case following the vertical angle to the movement of telescope, SD(Slope Distance) and VD(Vertical Distance) will be changed according to the movement of telescope. Occ. Point Operating procedure Operation Display 1 Press [F6](MORE) key from programs menu to get to the next page of programs. 2 Press [F2](OFFSET) key. 3 Press [F1](ANGLE OFFSET) key. [F6] [F2] [F1] Programs F1 BS pF2 STORE p F3 REM p F4 MLM p 4/7 MORE Programs F1 LINE p F2 OFFSET p F3 EXT.LINK p 7/7 MORE OFFSET MEASUREMENT 1.ANGLE OFFSET 2.DIST. OFFSET 3.PLANE OFFSET 4.COLUMN OFFSET ANGLE OFFSET 1.FREE V-ANGLE 2.HOLD V-ANGLE 5-15 5 PROGRAM MODES 4 Select the vertical angle [FREE] or [HOLD]. *1) [F1]or [F2] 5 Collimate prism P, and press the [F1](MEAS) key. *1) The horizontal distance from the instrument to the prism will be measured. Collimate P [F1] 6 Collimate point A0 using the horizontal motion clamp and horizontal tangent screw. Collimate A0 7 To show the slope distance of point A0, press the [F2](SD) key. [F2] 8 To show the coordinates, press the [F3](NEZ) key. *2) [F3] *1) To set the prism height or instrument height, press the [F5](HT) key. *2) To repeat angle offset measurement, press the [F1](NEXT) key. The display will return to step 5. ANGLE OFFSET HD: m MEAS HT ANGLE OFFSET HD* < m MEAS HT ANGLE OFFSET HR: 20°30'40" HD: 20.000 m VD: 0.000 m NEXT SD NEZ REC ANGLE OFFSET HR: 30°00'00" HD: 20.000 m VD: 0.000 m NEXT SD NEZ REC ANGLE OFFSET V : 90°00'00" HR: 30°00'00" SD: 20.000 m NEXT HD NEZ REC ANGLE OFFSET N : 17.321 m E : 10.000 m Z : 0.000 m NEXT SD HD REC 5-16 5 PROGRAM MODES 5.6.2 Distance Offset Measurement The measurement of a place apart from a prism is possible by inputting offset horizontal distance of front and back / right and left. Forward HD A 1 A0 oHD sign RorL HD Prism height Prism P Occ.Point Instrument height When measuring coordinates of ground point A1: Set the instrument height / prism height. When measuring coordinates of point A0: Set the instrument height only. (Set the prism height to 0 ). Operating procedure Operation Display 1 Press [F6](MORE) key from programs menu to get to the next page of programs. 2 Press [F2](OFFSET) key. 3 Press [F2](DIST. OFFSET) key. Previous offset value screen will appear. dFR: Forward/Rear offset value dRL: Right/Left offset value [F6] [F2] [F2] Programs F1 BS pF2 STORE p F3 REM p F4 MLM p 4/7 MORE Programs F1 LINE p F2 OFFSET p F3 EXT.LINK p 7/7 MORE OFFSET MEASUREMENT 1.ANGLE OFFSET 2.DIST. OFFSET 3.PLANE OFFSET 4.COLUMN OFFSET DIST. OFFSET dFR : 0.000 m dRL : 0.000 m OK INP 5-17 4 If you reset the offset value, press the [F6](INP) key and input the value. *1) [F6] DIST. OFFSET dFR : dRL : 0.000 m EXIT BS 5 Collimate prism using the horizontal motion clamp and horizontal tangent screw. Press the [F1](MEAS) key. *2) Collimate P [F1] DIST. OFFSET HD: m MEAS HT 5 PROGRAM MODES 0.000 m The offset measurement data will be shown. 6 To show the slope distance of point A0, press the [F2](SD) key. [F2] 7 To show the coordinates, press the [F3](NEZ) key. *3) [F3] DIST. OFFSET HR: 30°00'00" HD: 20.000 m VD: 0.000 m NEXT SD NEZ REC DIST. OFFSET V : 90°00'00" HR: 30°00'00" SD: 20.000 m NEXT HD NEZ REC DIST. OFFSET N : 17.321 m E : 10.000 m Z : 0.000 m NEXT SD HD REC *1) To skip the input, press the [F1](OK) key. *2) To set the prism height or instrument height, press the [F5](HT) key. *3) To repeat the offset measurement, press the [F1](NEXT) key. The display will return to step 5. 5-18 5 PROGRAM MODES 5.6.3 Plane Offset Measurement Measuring will be taken for the place where direct measuring can not be done, for example distance or coordinate measuring for a edge of a plane. Three random target points (P1, P2, P3) on a plane will be measured at first in the plane offset measurement to determine the measured plane. Collimate the measuring target point (P0) then the instrument calculates and displays coordinate and distance value of cross point between collimation axis and of the plane. P P P23PTarget heights of P1 to P3 is set to zero automatically. Edge (Prism) (Prism) (Prism) (Point without prism) Operating procedure Operation Display 1 Press [F6](MORE) key from programs menu to get to the next page of programs. 2 Press [F2](OFFSET) key. 3 Press [F3](PLANE OFFSET) key. Measurement screen of three points on a plane will be shown. [F6] [F2] [F3] Programs F1 BS pF2 STORE p F3 REM p F4 MLM p 4/7 MORE Programs F1 LINE p F2 OFFSET p F3 EXT.LINK p 7/7 MORE OFFSET MEASUREMENT 1.ANGLE OFFSET 2.DIST. OFFSET 3.PLANE OFFSET 4.COLUMN OFFSET PLANE OFFSET N001# SD : m MEAS HT 5-19 5 PROGRAM MODES 4 Collimate prism P1, and press the [F1](MEAS) key. Measuring will start. After measuring, the second point measurement screen will be shown. Collimate P1 [F1] 5 Measure the second and third prism in the same way. *1) The instrument calculates a...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: