COMPAQ, the Compaq logo, and Presario Registered U.S. Patent and Trademark Office. All other product names mentioned herein may be trademarks or registered trademarks of their respective companies. First Edition November 2000. s 7 line! 221490-371

SCSI Problems Some common causes and solutions for SCSI device problems are listed in the following table. Table 4-10 Solutions for SCSI Problems Problem Possible Solution System will not boot from a SCSI drive. Be sure that drive cabling and jumpers are set correctly. To boot to a SCSI drive, the drive with the lowest SCSI number will be the boot drive. No two drives can have the same SCSI number. See Figures 6-3, 6-4, and 6-5 for instructions on selecting SCSI ID. Compaq Professional Workstati

Take the included VGA cable and connect the male end of the cable to the VGA port on the back of the computer. Connect the female end of the VGA cable to the Adapter. 2. Take the included USB cable and connect it to the USB port on the back of the computer. Connect the other end of the USB cable to the Adapter. Follow these steps if you are using a Legacy Sun system 1. Shut down your computer. Take the included 13W3 cable and connect the end of the cable to the 13W3 port on the back of the co

Plugging and unplugging cables while servers are powered on may cause irreversible damage of the servers and/or the LCD Rack Console. Belkin is not responsible for damage caused in this way. You are now ready to begin installation of your LCD Rack Console. The following sections (pages 11–13) provide complete instructions for the hardware setup of a single LCD Rack Console (F1DC108C-US, F1DC116C-US). 1 2 3 4 5 6 7 8 section 11 Installation Connecting Servers to the LCD Rack Console (PS/2 Connect

See the “Updating Firmware” section in this User Manual. Q: How does the LCD Rack Console allow the user to switch between ports? A: The LCD Rack Console supports two methods of port selection. The user can select servers using specially designated keyboard hot keys or through the On-Screen Display. Q: How far can the server be from the LCD Rack Console? A: The LCD Rack Console can be placed up to 25 feet away from your PS/2 server and up to 15 feet away from your USB server. Q: What is the maxi

Using DDC, a monitor can inform a computer’s video card about its properties, such as maximum resolution and color depth, to ensure that the user is presented with valid options for configuring the display. Daisy-Chain: A configuration of multiple KVM switches that are connected one to another in a series. A KVM switch daisy-chain uses common settings to allow seamless, complex interactions between multiple consoles for control over many servers. HID: Human Interface Device, the USB device class

Boeing Avenue 333 1119 PH Schiphol-Rijk, The Netherlands +31 (0) 20 654 7300 +31 (0) 20 654 7349 fax Belkin GmbH Hanebergstrasse 2 80637 Munich, Germany +49 (0) 89 143405 0 +49 (0) 89 143405 100 fax Belkin SAS 130 rue de Silly 92100 Boulogne Billancourt, France +33 (0) 1 41 03 14 40 +33 (0) 1 41 31 01 72 fax © 2005 Belkin Corporation. All rights reserved. All trade names are registered trademarks of respective manufacturers listed. RK1004ek INSTRUCTIONS RK1004ek Product Inventory IEC power suppl

All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Operating Door Swing Handle Instructions 1. The doors on your RK1004ek Enclosure are reversible. Open the door and lift it off of its hinges. 2. Remove the male and female hinge parts from the Enclosure and the door. 3. Reverse them and re-install to allow left-hand door swing. 4. Remove swing handle and reverse. Mounting Rails Rails can be adjusted front to rear by loosening the 1/4” (6mm) - 20 he

Install top angles to vertical upright channels. a. Lay vertical upright channels on edge so tapped holes face you and the floor. Be sure open sides of upright channels face each other. b. Align holes in top angle with corresponding holes in vertical uprights. Formed leg of top angle should be facing toward you. c. Install hex head bolts and lock washers. Finger tighten only. d. Turn vertical upright over (rotate 180 degrees) and repeat steps (a) through (c). Finger tighten only. Top Angle Hex B

All rights reserved. All trade names are registered trademarks of respective manufacturers listed. Instructions (cont’d.) 2. Install base angles to vertical upright channels. a. Leaving vertical upright channels on edge, align holes in base with corresponding holes in each upright channel. Long leg of base should be facing you. b. Install 4 hex head bolts and lock washers. Finger tighten only. c. Turn vertical upright assembly over (rotate 180 degrees) and repeat steps (a) and (b). Finger tighte