Оценок - 2, средний балл: 4 ( )

Производитель: Kenwood Размер: 796.78 kb Название файла: Язык инструкции:

. You can also check with the n. and a. peak level indicators. Each press of the MODE key changes the setting. 1 “LEVEL” lights up: Recording level setting mode 2 “BAL.” lights up: Recording balance setting mode 3 “BIAS” lights up: Recording bias setting mode (Deck B of the CT-2050/KXF-W6010 only) 4 “LEVEL”,“BAL.”,and “BIAS”go off: Counter display mode lights up 0dB. Recording level display. OAdjust the recording level so that the 0 dB of the peak level indicators sometimes lights up. OThe recording level can be adjusted on both decks A and B. (CT-203/ KXF-W4010; Deck B only) Set the recording level. AUTO BIAS 3 1Play a music source. 2Enter the record-pause mode. 8PAUSE ¦REC/ARM 3Press the MODE key and select the "BAL." mode. MODE 4Adjust the recording balance. REC LEVEL/BAL. /BIAS ° MAX/R ° MIN/LRight sound decreases. Left sound decreases. 5Press the MODE key and select the "LEVEL" mode. MODE 6Adjust the recording level. REC LEVEL/BAL. /BIAS ° MAX/R ° MIN/LRecording level decreases. Recording level increases. 7Stop playing the source. CT-2050/KXF-W6010 CT-203/KXF-W4010 How to record (CT-203/KXF-W4010; Deck B only) CT-2050/203/KXF-W6010/W4010 (En/M) 4 4 Start recording. ORecording will start. OThe deck enters the stop mode automatically when the tape has been recorded till the end. Press once. 1Press the REC/ARM (¦) key. 2Play the music source from the begin- ning. ¦REC/ARM CT-2050/KXF-W6010 CT-203/KXF-W4010 Bias level adjustment (Deck B of the CT-2050/KXF-W6010 only) The MODE key can be used to adjust the bias level. Each press of the MODE key changes the setting. 1 “LEVEL” lights up: Recording level setting mode 2 “BAL.” lights up: Recording balance setting mode 3 “BIAS” lights up: Recording bias setting mode (Deck B of the CT-2050/KXF-W6010 only) 4 “LEVEL”,“BAL.”,and “BIAS”go off: Counter display mode lights up OTo adjust the bias level, play back the recorded sound and adjust to the suitable level.Repeat if necessary. OThe bias can be adjusted to a value of ±3. 1Press the MODE key and select the "BIAS" mode. 2Adjust the bias level. MODE REC LEVEL/BAL. /BIAS ° MAX/R ° MIN/L The high frequency decreases. The high frequency increases. How to use the MPX FILTER key Use this function when recording a radio (FM) broadcasts. Depending on the tuner, a recorded FM broadcast may produce a “beat” sound. In this case, press the MPX FILTER key before recording. To cancel, press the MPX FILTER key again. lights up MPX FILTER How to record (CT-203/KXF-W4010; Deck B only) CT-2050/203/KXF-W6010/W4010 (En/M) To pause recording temporarily To stop recording Pause To resume recording OThe 8indicator lights. 8PAUSE ¦REC/ARM 2Stop playing the source component. 237CT-2050/KXF-W6010 CT-203/KXF-W4010 1Stop the tape transport. How to provide non-recorded blanks between programs In stop mode During recording Press successively twice. Press once. ¦REC/ARM ¦REC/ARM OAfter leaving a non-recorded blank of about 4 seconds, the deck enters the record-pause mode. During recording in the 2direction: During recording in the 3direction: 1Rewind during recording. 2Press the REC/ARM (¦) key twice. 3Replay the tune you wish to record. 4Press the REC/ARM (¦) key once. A 1 A 1 ¦REC/ARM ¦REC/ARM CT-2050/KXF-W6010 CT-203/KXF-W4010 To start recording again from the biginning The following procedure is useful when you want to cancel recording in progress and re-start it. A non-recorded space of about 4 seconds or more should be reserved before the position where recording was started. OWhen the A(or 1) key is pressed during recording, recording is aborted and tape is rewound as shown below if there is a non-recorded space of more than 4 seconds before the recording start position. Tape stops after 2 sec. of transport. Tune to be re-recorded.Recorded tune Re-recording Blank of 4 sec. or more. OIf there is no recorded tune before, the tape will be rewound then stopped. OWhen re-recording from the beginning of tape, feed the leader tape (the first portion of tape that cannot be recorded) before starting rerecording. OA non-recorded space of about 4 seconds is reserved on tape, then the tape transport stops. ORecording starts. Relay recording (CT-2050/KXF-W6010 only) CT-2050/203/KXF-W6010/W4010 (En/M) This function allows to record sound continuously from deck A to B. Since this unit is not designed for recording with metal (TYPE ) tapes, do not use metal tapes for recording. Preparation Make “Playback (recording) preparation”. 0(If relay recording is required, insert tapes in both decks A and B. Select the record- ing mode to set to "O" or "[" only.) : Keys and control used in the operations described on this page. Relay recording 1 1 Set the relay recording mode. "RELAY" lights up. RELAY REC 2 2 Perform auto-bias adjustment. (The bias adjustment is applied to deck B.) AUTO BIAS 3 3 Adjust the recording level. 1Play the music source. 2Set the record-pause mode. (deck A). 3Adjust the recording balance and record- ing level. ^ 4Stop playing the music so...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: