Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
This access hole must be plugged with a non-combustible insulation after the gas supply line has been installed. Si le foyer prefabrique ne comporte pas d’orifices d’amenee du gaz, un orifice d’au plus 37,5 mm (1,5 po) peut etre pratique, selon les regles de l’art, dans la partie inferieure des parois ou au fond de la chambre de combustion. Cet orifice doit etre obture au moyen d’isolant incombustible une fois la conduite de gaz en place. The installer must mechanically attach the marking supplied with the gas fireplace insert to the inside of the firebox of the fireplace into which the gas fireplace insert is installed. Log Set Installation If logs are not installed according to the log installation instructions, flame impingement and improper combustion could occur and result in soot and/or excessive production of carbon monoxide (CO), a colorless, odorless, toxic gas. The size and position of the log set is critical to achieve a safe, reliable and attractive flame pattern. Any attempt to use a different log set in the fireplace will void the warranty and will result in incomplete combustion, sooting, and poor flame quality. *Brick Panels are not offered for the SDVI Gas Insert. 1. Remove log rack (2 screws) and install rear log on retainer. See Figures 7 and 8). 2. Reinstall log rack with rear log. IMPORTANT!!! SCREWS PASS THROUGH LOG RACK AND BURNER PAN. 3. Install light layer of mineral wool directly over ports. See Figure 9. -A light layer will give a more constant rear flame. -A heavy layer will give more glow, but will need to be adjusted after light up. 4. Install front logs on retainer slots. See Figure 10. 5. Place top log on pin. See Figure 11. 6. Place black embers around perimeter of mineral wool. Important!!! Do not cover ports with black embers. See Figure 11. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 2 Screws Figure 7 Rear Log Retainer Figure 8 Figure 9 12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Figure 10 Surround Panels Installation The SDVI insert surround panels are made of heavy gage steel for durability and, if desired, for the ease of making an inside fit in the fireplace. 1. Remove the speed nuts (A in Figure 12) from the parts bag and install (with the flat surface forward) on the six holes in the surround brackets - three on each side of the insert (B in Figure 12). A flat bladed screwdriver may help in installing the nuts. 2. Install all surround panels and trim with the insert positioned in the fireplace but a few inches in front of its final location. 3. Install the side surround panels by lining up the holes in the tabs on the side surround panels in front of the holes on the surround brackets. Next insert two slotted 1/4" truss screws for each side surround panel and secure loosely. Face Installation The faces come with hooked brackets. To install the face, hang the hooked brackets on the surround brackets per instructions provided in decorative face kit (C in Figure 12). Figure 12 A B C Spring Handle Latches Door Mounting Plates 4. Fasten top surround panel with the remaining two truss screws. Tighten all six truss screws after adjusting the surround panels to eliminate space between side and top surround panels. 5. Assemble the surround trim by inserting the elbowed retainer in the rectangular slot in the ends of the longest piece of trim and secure by tightening the screw in the retainer. Slide the mitred ends of the two side trim pieces onto the elbowed retainer and secure by tightening the retainer screw. 6. The fastened trim pieces should now be horseshoe shaped. Slide the trim down over the surround panels so the edge of the surround panel fits just behind the rounded edge of the trim. 7. Install three spring clips (found in parts bag in firebox) in each piece of trim by inserting them between the rear of the surround panel and the channel of the trim. The spring clips will push the trim tight to the surround panel. Install front logs on retainer slots Place Top Log On Pin Top Log Ports Front Logs Figure 11 Gas Line Installation Gas Line Installation CAUTION: Specific hearth requirements apply (see Clearances to Combustibles). The SDVI gas insert must be connected to the gas line in accordance with local codes and/or the National Fuel Gas Code, ANSI Z223.1 (In Canada, the current CAN/CSA B149.1 installation code). The insert comes with an 8" nipple attached to the supply side of the gas valve. After connecting the gas line, all joints in the line and connections at the valve should be checked for leaks before final positioning of the unit. Conduct a gas leakage test of the appliance piping and control system downstream of the shutoff valve in the supply line to the appliance. Gas Pressure Requirements A MAJOR CAUSE OF OPERATING PROBLEMS WITH GAS APPLIANCES IS IMPROPER GAS PRESSURE! The most important item to check during the initial installation and the first thing to check when operating problems occur is gas pressure! This appliance will not function p...
Эта инструкция также подходит к моделям:Камины - SDVI (4.14 mb)
Камины - SDVI (4.14 mb)
Камины - SDVI (4.14 mb)
Камины - SDVI (4.14 mb)