Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
Do not operate the insert with the glass removed. Glass Door Cleaning And Maintenance Cleaning: Do not remove or clean the glass door when hot. When cool, the glass may be cleaned with a clean, soft cloth and a household glass cleaner. For cleaning white condensation from the interior glass, use a gas fireplace glass cleaner available from your dealer. Use of caustic or abrasive cleaners may damage the glass. DO NOT spray commercial glass cleaner with ammonia on the door and glass gasket as it may dissolve the gasket glue. Repair: If the glass is broken in the glass door, the entire door (metal frame, gasket and glass) should be replaced as a unit. This replacement glass door is available from your Lennox Hearth Products dealer. Do not use substitute parts or materials. The glass is neo-ceramic and alternative types must not be used. NOTE: BE CAREFUL NOT TO SPRAY COMMERCIAL GLASS CLEANER WITH AMMONIA ON GASKET AREA OF DOOR. AMMONIA WILL DISSOLVE GASKET GLUE. Only doors certified with the appliance shall be used. Seules des portes certifiees pour cet appareil doivent etre utilisees. CAUTION: DO NOT abuse glass door by striking or slamming shut. Do not remove glass door while the appliance is hot. WARNING • Do not attempt to substitute the materials used on these doors, or replace cracked or broken glass. • Handle this glass with extreme care! Glass is susceptible to damage – Do not scratch or handle roughly while reinstalling the glass door frame. • The glass door(s) of this appliance must only be replaced as a complete unit as provided by the manufacturer. Do not attempt to replace broken, cracked or chipped glass separately. • Do not attempt to touch the front enclosure glass with your hands while the appliance is in use. WARNING Do not operate appliance with the glass front removed, cracked or broken. AVERTISSEMENT Ne pas utiliser l'appareil si le panneau frontal en verre n'est pas en place, est craque ou brise. Fuel Conversion Fuel Conversion Conversion Kit: Please see instructions provided with conversion kit. Blower Removal Unplug the power supply cord from the electrical outlet prior to removing the blower. The blower can be accessed through the back wall of the firebox. Remove the insert face, glass door and log set. All of these items are fragile so handle them with care. Next, remove the nine allen head screws around the outside of the panel fastened to the back wall of the firebox. Rotate the top of this panel toward the front, remove the two wires connected to the blower, and then lift the panel with the blower attached out of the firebox. To reinstall the blower, repeat these steps in the reverse order. Blower Wiring Schematic Electrical Requirements: This gas insert operates without an outside power source, however the blower requires a 120 Volt electrical service outlet. This appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, the National Electrical Code ANSI/NFPA 70 - latest edition. (See Operating Options for thermostat and ON/OFF switch information). CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. ATTENTION: Au moment de l'entretien des commandes, etiquetez tous les fils avant de les debrancher. Des erreurs de cablage peuvent entrainer un fonctionnement inadequat et dangereux. Blower Snap Switch Green (Ground) Black (Hot)From Power Source Speed Control White (Neutral) Black White Blower Figure 21 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. TROUBLESHOOTING TROUBLESHOOTING IMPORTANT: Call your gas supplier or plumber for additional help with any gas control problem. Valve system troubleshooting should only be accomplished by a qualified service technician. SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Thin black coating (soot) Improper log or ember See Log Set Installation on Page 11. If there is soot in one specific location, the forms on the viewing placement rockwool below this location needs to be adjusted. This can be done by pulling embers glass, logs, or firebox Improper air shutter setting Not enough combustion air forward slightly. If the flames have soot tails, the shutter will need to be opened. If sooting continues open air shutter (see Air Shutter Adjustment on Pages 13 and 14). Check for debris obstructing air flow in valve compartment under insert or in front of lower venting. Humming or whistling Normal operating noise See Quiet Operation on Page 18. The noise may be reduced by slightly turning down the coming from insert. Obstructed orifice opening flame. Turning the flame down will reduce the heat output of the insert. If noise is excessive or is “whistling” have your gas supplier check the regulator and orifices and replace if necessary. A change in flame appear-A change in gas pres-Have your gas supplier check for correct gas pressure (7" W.C. / po. C.E. [1.74 kPa] natuance or burner operation. sure Improper ember placem...
Эта инструкция также подходит к моделям:Камины - SDVI (4.14 mb)
Камины - SDVI (4.14 mb)
Камины - SDVI (4.14 mb)
Камины - SDVI (4.14 mb)