Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
wire Figure 11 Blower Kit Installation To install the blower kit, follow Steps 1 thru 5 and refer to Figures 12, 13 and 14. Step 1. Locate the blower motor shield. Step 2. Remove the motor shield by bending it along the perforation until the tabs break away. Step 3. With the motor shield removed, place the blower in the unit with the power cord up and slide to the back of the unit until the motor is behind the rear support. Step 4. Rotate the blower 90 degrees, so that the discharge is up. Step 5. Move left side of blower around until it is in the proper position and bend the retaining tabs in the bottom of the unit up into the slots on the blower. Blower Motor Motor Shield Figure 12 Perforation Tabs Motor Shield Removed Figure 13 Rotated Blower In Final Position Figure 14 NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. FIREBOX FINISHES FIREBOX FINISHES Only noncombustible materials like marble, stone, tile, brick, etc. may overlap the black front facing but be sure not to block the upper or lower grilles. Seal all joints between the black facing and wall surrounds to prevent air intrusion. Use noncombustible caulking material only to seal the black metal facing to the surround material on the finished wall. REPLACEMENT PARTS An exploded view of the firebox with numbered parts and a replacement parts list can be found on page 11. Normally, all parts should be ordered through your distributor or dealer. Parts will be shipped at prevailing prices at time of order. When ordering repair parts, always give the following information: 1. The model number of the firebox. 2. The serial number of the firebox. 3. The part number. 4. The description of the part. 5. The quantity required. 6. The installation date of the firebox. If you encounter any problems or have any questions concerning the installation of a unvented heater in this system, please contact your distributor or dealer. ACCESSORIES AND COMPONENTS (FBK-200 Models Only) Blower Kits -Single Speed -Variable Speed 80L84 80L85 FBK-100 FBK-200 Blower Kit The FBK-100 blower provides for a constant velocity forced air circulation feature for your appliance. The FBK-200 assembly with variable speed wall switch provides a forced air circulation feature for your appliance. Decorative Volcanic Stone 80L42 FDVS Decorative Volcanic Stone The decorative volcanic stone, Model FDVS, can be used to enhance the look of your appliance. Decorative volcanic stone is standard with this appliance. Order model FDVS for replacement of stone when needed. Spread the decorative volcanic stone evenly around the bottom of the firebox. NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE. 11 REPLACEMENT PARTS UVF-500 UVF-600 No. DESCRIPTION Part No. Qty. Part No. Qty. Gas Fireplace Assembly – – – – 1. Firescreen 36L89 2 36L99 2 2. Rod, Screen 88L95 2 88L96 2 3. Refractory, Side 88L59 2 88L65 2 4. Refractory, Rear 88L58 1 88L64 1 5. Refractory Base 88L57 1 88L63 1 6. Canopy 96L27 1 96L28 1 3 4 5 2...
Эта инструкция также подходит к моделям:Камины - UNVENTED FIREBOXES UVFC-600 (2.24 mb)
Камины - UNVENTED FIREBOXES UVFC-500 (2.24 mb)
Камины - UNVENTED FIREBOXES UVFC-500 (2.24 mb)
Камины - UNVENTED FIREBOXES UVFC-600 (2.24 mb)