Оценок - 1, средний балл: 3
(
)
)
|
Фрагмент инструкции
14 Figure 13: Linear Heater Assembly Overview ........................ 15 Figure 14: Linear Heater Layout Overview.............................. 16 Figure 15: Linear Heater Layout Overview (Continued) .......... 17 Figure 16: U-Tube Heater Assembly Overview ......................23 Figure 17: U-Tube Heater Layout Overviews .........................24 Figure 18: U-Tube Heater Layout Overviews (Continued).......25 Figure 19: Reflector Joint Detail..............................................27 Figure 20: Gas Connection with Flexible Gas Hose ...............40 SECTION 1: HEATER SAFETY SECTION 1: HEATER SAFETY Your Safety is Important to Us! This symbol is used throughout the manual to notify you of possible fire, electrical or burn hazards. Please pay special attention when reading and following the warnings in these sections. Installation, Service and Annual Inspection of heater must be done by a contractor qualified in the installation and service of gas-fired heating equipment. Read this manual carefully before installation, operation or service of this equipment. This heater is designed for heating nonresidential indoor spaces. Do not install in residential spaces. These instructions, the layout drawing, local codes and ordinances, and applicable standards that apply to gas piping, electrical wiring, venting, etc. must be thoroughly understood before proceeding with the installation. Thin sheet metal parts, including the aluminum reflector portion of the heater and the various venting components, have sharp edges. To prevent injury, the use of work gloves is recommended. The use of gloves will also prevent the transfer of body oils from the hands to the surface of the reflector. Before installation, check that the local distribution conditions, nature of gas and pressure, and adjustment of the appliance are compatible. 1.1 Manpower Requirements To prevent personal injury and damage to the heater, two persons will be required for installation. TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL SECTION 2: INSTALLER RESPONSIBILITY The installer is responsible for the following: • To install the heater, as well as the gas and electrical supplies, in accordance with applicable specifications and codes. Roberts-Gordon recommends the installer contact a local building inspector or Fire Marshal for guidance. • To use the information given in a layout drawing and in the manual together with the cited codes and regulations to perform the installation. • To install the heater in accordance with the Clearances to Combustibles. • To furnish all needed materials not furnished as standard equipment. • To plan location of supports. • To provide access to burners for servicing on all sides for burner removal. • To provide the owner with a copy of this installation, operation and service manual. • To never use heater as support for a ladder or other access equipment and never hang or suspend anything from heater. • To ensure there is adequate air circulation around the heater and to supply air for combustion, ventilation and distribution in accordance with local codes. • To safely and adequately install heater using materials with a minimal working load of 75 lbs (33 kg). 2.1 Wall Tag A laminated wall tag is available for the heater as a permanent reminder of the safety instructions and the importance of the required clearances to combustibles. Please contact Roberts-Gordon or your ROBERTS GORDON® independent distributor to obtain the wall tag. Affix the tag by peeling off the backing of the adhesive strips on the rear surface and position the tag on a wall near the heater (e.g. thermostat or ROBERTS GORDON® BZC Controller). A copy of the wall tag (P/N 91037912) is illustrated on the back cover. For an immediate solution, you may affix this copy on the wall near the heater. Know your model number and installed configuration. Model number and installed configuration are found on the burner and in the Installation, Operation and Service Manual. See Page 3, Figure 1 through Page 6, Figure 10. Write the proper clearance dimensions in permanent ink according to your model number and configuration in the open spaces on the tag. 2.2 Corrosive Chemicals 6. . . . . . . Roberts-Gordon cannot be responsible for ensuring that all appropriate safety measures are undertaken prior to installation; this is entirely the responsibility of the installer. It is essential that the contractor, the sub-contractor, or the owner identifies the presence of combustible materials, corrosive chemicals or halogenated hydrocarbons* anywhere in the premises. * Halogenated Hydrocarbons are a family of chemical compounds characterized by the presence of halogen elements (fluorine, chlorine, bromine, etc.). These compounds are frequently used in refrigerants, cleaning agents, solvents, etc. If these compounds enter the air supply of the burner, the life span of the heater co...
Эта инструкция также подходит к моделям:Электрообогреватели - Vantage TF TF-120 (5.17 mb)
Электрообогреватели - Vantage TF TF-160 (5.17 mb)
Электрообогреватели - Vantage TF TF-200 (5.17 mb)
Электрообогреватели - Vantage TF TF-250 (5.17 mb)