Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Never use a propane tank with a damaged valve connection. " The propane tank must be constructed and marked in accordance with the specifications for LP gas cylinders per the US Department of Transportation (DOT). * The propane tank must be designed to provide for vapor withdrawal from the operating cylinder. * Never connect an unregulated propane tank to the heater. LEAK TESTING * Gas connections on the heater are gas tested at the factory prior to shipment A complete gas tightness check must be performed at the installation site due to potential shipment irregularities or excessive pressure being applied to the heater as well as to check final installation of components by the consumer. TO LEAK TEST * Make a soapy solution of one part liquid detergent and one part water. The soap solution can be applied with a spray bottle, brush, or rag. Soap bubbles will appear where a leak is present. * Make certain the safety control valve is in the “OFF” position (at the control panel of the head unit). * Turn the gas supply “ON” at the propane cylinder valve. Apply/spray several drops on the regulator hose to gas inlet hose connection, and the regulator to tank cylinder connection, (small bubbles indicate a leak) * If a leak is present, turn “OFF” the gas supply, loosen and then re-tighten and leaking fittings, turn gas supply “ON” again and recheck. Repeat as needed. BE CAREFUL: When certain material or items are left under this space heater while in use, they will be subjected to radiant heat and could be seriously damaged! r The heater is primarily for heating of outdoor patios, decks, spas, pools and outdoor home working areas. * This unit is designed for RESIDENTIAL use only! ' Always ensure that adequate fresh air ventilation is provided. Follow the MINIMUM spacing tolerances as indicated AT ALL TIMES! * The installation must conform to local codes, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases, ANSI/NFPA 58 or NFGC, ANSIZ 223.1-1998 * The heater must be placed on stable, level firm ground * Never operate in an explosive atmosphere. Keep away from areas where gasoline or other flammable liquids or vapors are stored or used. A CAUTION In very strong winds, turn off the heater, turn off the gas cylinder valve and remove the heat reflector hood. Then move the heater to a sheltered location. Do not move heater while it is still hot. PAGE 10 **• IMPORTANT NOTICE - Do NOT return to place of purchase?!! Please contact our Toll Free Hotline: (866)985-7877 E-mail, cservice@welltraveled.net STORAGE B-1 OPERATION 1 Open the gas cylinder valve ? Turn the control knob half way between Ihc small flame ar»d Ihn laige flane symbols. 3 Depress (press down) the control knob and then push the RED igniler button to ignite Ihe main bumei, repeal until the mam burner ignites Keep the control knob fully depressed for an additional 30 seconds after Ihe burner ignites, then release Ihe control button 4 To increase the flame .turn ihe control knob clockwise T o decrease Ihc flame,turn Ihc control knob counter clockwise b. I o turn olt lire appliance press down the control knob and turn Clock wise the off position. 6 Wait b minutes befuie le lighting the unit 7 Completely shut off and close gas cylinder valve *** IMPORTANT NOTICE *** Establishing a burner IgnTHon for fhe FIRST lime or after changing the cylinder tank may take up to 2-3 minutes in order for the gas to purge through the feeder lines. •*THINK SAFETYI*** After aooliancc shut down. Do NOT touch or move unit for at least 30 minutes. This allows Гог proper cooling of heater components. * NOTICE * •“NQTE. Main bumcr.n!imalag.iHLlilnain.a а.МА1£Н1^ CAUTION: tie aware и I gas build-up when ¡ighU/ig with match-e specially after holding down control knob. If you smeli gas. WAIT 5 minutes for gas to dissipate before lighting. Purina im FIRST TIME use only. It is normal to cxpcrcncc a smal amount ol smoke coming from the reflector hood This is due to If»« b.irn off of Ihe protective coating applied durir.j ihe manufacturing process Manual Lighting: pljco a sticker lykcr thru the largo hole al the botton' of the Sumer unit wniie following the lighting procedu'es above WARNING: Reas the inslal ation. operation, anc maintenance instruc lions thoroughly Bbl-OKb operating, installing or servic ng this equipment. Improper use, adjustment, service and/or mainlenarre can cause serious injury or damage to your property Min mum Clearance to adjacent combustible surfaces s as follows ‘Sides - 24* *Too • 36“ The Gas Supply Must be turned "OFF’' at the LP Gas Cylinder when this appliance i9 not in use. *** IMPORTANT NOTICE *** - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltraveled.net *** BURNER OPERATION *** * The burner head unit emitter screen will burn bright red when operating normally. The heat generated is...