Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации Cadet, модель 2F350

Производитель: Cadet
Размер: 222.71 kb
Название файла:

Язык инструкции:enes

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to one thermostat wire (typically marked L1). 3. Route remaining thermostat wire (typically marked T1) to the baseboard heater. 4. Route remaining supply and ground wire to the baseboard heater. 5. Follow installation instructions for mounting and wiring baseboard heater. Figure 12To Supply Thermostat wiring box Single Pole Thermostat L1 T1To Heater DOUBLE POLE WALL THERMOSTAT 1. Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to one thermostat wire (typically Thermostat marked L1). wiring box 3. Connect remaining supply wire to other thermostat wire (typically marked L2). 4. Route remaining thermostat wires (typically marked T1 and T2) to the baseboard heater. 5. Route ground wire to the baseboard heater. 6. Follow installation instructions for mounting and wiring baseboard heater. Figure 13 OFFDouble Pole Thermostat L2 T2 L1 T1 To Supply To Heater MULTIPLE BASEBOARD WIRING. 240V SUPPLY ONLY (See Figure 14) 1. Left side wiring: disconnect factory connector A. Right side wiring: disconnect factory connector B. 2. Connect one wire from each heater to one supply wire. 3. Connect remaining wire from each heater to the remaining supply wire. 4. Connect supply ground wire to both ground screws using appropriate guage wire. Note: Field wiring is not provided Multiple Baseboard Wiring - Optional Follow the instructions below if you are wiring more than one heater in parallel on same circuit. If you are wiring multiple baseboards to one control, it is recommended that you use one control per room. B Do not disconnectField Wiring GroundGround Field WiringHeater Wires To Wall Thermostat ABaseboard Heater Right Side Baseboard Heater Left Side Figure 14 STANDARD BASEBOARDS SHOWN Operation & Maintenance Operation & Maintenance How To Operate Your Heater 1. Heater must be properly installed before it is used. Switch the power on at the electrical panel board. PLEASE NOTE: Upon initial start-up, the heater may emit a burning odor. This is not dangerous, and is due to a protective lubricant used during the manufacturing process. It typically dissipates within several hours. 2. Turn the thermostat fully clockwise. 3. When the room reaches your comfort level, turn the thermostat knob counterclockwise until a clicking sound is heard (if using a digital thermostat, set at desired room temperature). The baseboard will automatically cycle around this preset temperature. Maintenance Cadet electric baseboards are virtually maintenance-free. However, a certain amount of lint and dust will accumulate inside the unit and should be periodically cleaned: 1. Turn the electrical power off at the electrical panel board (circuit breaker or fuse box) and lock or tag the panel board door to prevent someone from turning on power while you are working on the heater. Failure to do so could result in serious electrical shock, burns, ...

Эта инструкция также подходит к моделям:
Электрообогреватели - 3F750 (222.71 kb)
Электрообогреватели - 3F750-8 (222.71 kb)
Электрообогреватели - 4F1000 (222.71 kb)
Электрообогреватели - 5F1250 (222.71 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории