Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации Cadet, модель 8F2500-8

Производитель: Cadet
Размер: 222.71 kb
Название файла:

Язык инструкции:enes

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


Connect one supply wire to one heater wire. 2. Connect remaining supply wire to remaining heater wire. 3. Replace wiring compartment cover and secure with screw previously removed. 4. Turn power back on at the electrical panel board. Figure 8 Right Side Wiring ShownBaseboard Heater To Supply Side .B. Shown Supply Wires Ground STANDARD BASEBOARD WIRING ON LEFT SIDE 120V OR 240V SUPPLY (See Figure 9) 1. Connect one supply wire to one heater wire. 2. Connect remaining supply wire to remaining heater wire. 3. Replace wiring compartment cover and secure with screw previously removed. 4. Turn power back on at the electrical panel board. Figure 9 Left Side Wiring ShownBaseboard Heater To Supply Side .A. Shown Supply Wires Ground MULTI-WATT BASEBOARDS: WIRING ON RIGHT SIDE MODEL 8F2025 (See Figure 10) 1. Connect one supply wire to one heater wire. 2. Connect remaining supply wire to remaining heater wire. 3. Replace wiring compartment cover and secure with screw previously removed. 4. Selecting desired wattage a. For 2500 watt applications: No action is required. Heater is factory set for 2500 watts. b. For 2000 watt applications: Remove left wiring compartment cover. Cut red wire and cap both loose ends with approved wire connectors, or wrap both loose ends with electrical tape. Replace wiring compartment cover and secure with screw previously removed. 5. Turn power back on at the electrical panel board. Figure 10 Right Side Wiring Shown Side .B. Shown Supply Wires Ground Baseboard Heater To Supply Red Wire 2000 Watt Configuration Left Side of Baseboard Shown Red Wire DO NOT DISCONNECT MULTI-WATT BASEBOARDS: WIRING ON LEFT SIDE MODEL 8F2025 (See Figure 11) 1. Disconnect splice/wire connector without the red wire. 2. Connect one supply wire to the upper black wire. 3. Connect the other supply wire to the lower black wire. 4. Selecting desired wattage: a. For 2500 watt applications: No action is required. Heater is factory set for 2500 watts. b. For 2000 watt applications: Cut red wire and cap both loose ends with an approved wire connector, or wrap loose ends with electrical tape. 5. Replace wiring compartment cover and secure with screw previously removed. 6. Turn power back on at the electrical panel board. Model 8F2025 Factory set for 2500 watts Figure 11 Left Side Wiring Shown Baseboard Heater DO NOT DISCONNECT To Supply Red Wire Side .A. Shown Supply Wires Ground Red Wire Red Wire 2000 Watt Configuration Left Side of Baseboard Shown Baseboard wiring with a wall thermostat - Optional Refer to the wiring diagram below that corresponds to your thermostat application. Note: Wiring diagrams are for reference only. See wall thermostat instructions included with your thermostat for your specific application. For instructions on wiring using an in-built thermostat, see Cadet BTF1, BTF2 and SBFT2 Installation Instructions LOWSINGLE POLE WALL THERMOSTAT 1. Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to ...

Эта инструкция также подходит к моделям:
Электрообогреватели - 3F750 (222.71 kb)
Электрообогреватели - 3F750-8 (222.71 kb)
Электрообогреватели - 4F1000 (222.71 kb)
Электрообогреватели - 5F1250 (222.71 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории