Войти:
Оценок - 4, средний балл: 4.3 ( )

Инструкция по эксплуатации Cadet, модель 5F1250-8

Производитель: Cadet
Размер: 222.71 kb
Название файла:
Язык инструкции:enes
Перейти к скачиванию



Фрагмент инструкции


4. Selecting desired wattage a. For 2500 watt applications: No action is required. Heater is factory set for 2500 watts. b. For 2000 watt applications: Remove left wiring compartment cover. Cut red wire and cap both loose ends with approved wire connectors, or wrap both loose ends with electrical tape. Replace wiring compartment cover and secure with screw previously removed. 5. Turn power back on at the electrical panel board. Figure 10 Right Side Wiring Shown Side .B. Shown Supply Wires Ground Baseboard Heater To Supply Red Wire 2000 Watt Configuration Left Side of Baseboard Shown Red Wire DO NOT DISCONNECT MULTI-WATT BASEBOARDS: WIRING ON LEFT SIDE MODEL 8F2025 (See Figure 11) 1. Disconnect splice/wire connector without the red wire. 2. Connect one supply wire to the upper black wire. 3. Connect the other supply wire to the lower black wire. 4. Selecting desired wattage: a. For 2500 watt applications: No action is required. Heater is factory set for 2500 watts. b. For 2000 watt applications: Cut red wire and cap both loose ends with an approved wire connector, or wrap loose ends with electrical tape. 5. Replace wiring compartment cover and secure with screw previously removed. 6. Turn power back on at the electrical panel board. Model 8F2025 Factory set for 2500 watts Figure 11 Left Side Wiring Shown Baseboard Heater DO NOT DISCONNECT To Supply Red Wire Side .A. Shown Supply Wires Ground Red Wire Red Wire 2000 Watt Configuration Left Side of Baseboard Shown Baseboard wiring with a wall thermostat - Optional Refer to the wiring diagram below that corresponds to your thermostat application. Note: Wiring diagrams are for reference only. See wall thermostat instructions included with your thermostat for your specific application. For instructions on wiring using an in-built thermostat, see Cadet BTF1, BTF2 and SBFT2 Installation Instructions LOWSINGLE POLE WALL THERMOSTAT 1. Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to one thermostat wire (typically marked L1). 3. Route remaining thermostat wire (typically marked T1) to the baseboard heater. 4. Route remaining supply and ground wire to the baseboard heater. 5. Follow installation instructions for mounting and wiring baseboard heater. Figure 12To Supply Thermostat wiring box Single Pole Thermostat L1 T1To Heater DOUBLE POLE WALL THERMOSTAT 1. Route supply wires to the thermostat wiring box (if not already present). 2. Connect one supply wire to one thermostat wire (typically Thermostat marked L1). wiring box 3. Connect remaining supply wire to other thermostat wire (typically marked L2). 4. Route remaining thermostat wires (typically marked T1 and T2) to the baseboard heater. 5. Route ground wire to the baseboard heater. 6. Follow installation instructions for mounting and wiring baseboard heater. Figure 13 OFFDouble Pole Thermostat L2 T2 L1 T1 To Supply To Heater MULTIPLE BASEBOARD WIRING. 240V SUPPLY ONLY (See Figure 14) 1. Left side wiri...

Эта инструкция также подходит к моделям:
Электрообогреватели - 3F750 (222.71 kb)
Электрообогреватели - 3F750-8 (222.71 kb)
Электрообогреватели - 4F1000 (222.71 kb)
Электрообогреватели - 5F1250 (222.71 kb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории