Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
800-477-2267 ext. 230 support@peripheralelectronics.com GM Owner’s Manual Media GatewayPXAMG PGHGM3 ©2008 AAMP of Florida, Inc. Rev. 05-01-08 INST013 Table of Contents Pages 1. Introduction 1 2. Precautions 1 3. Compatibility 1 4. Dipswitch Settings 2 5. Installation 2 6. iPod Operation 3 7. HD Radio Operation (if equipped) 5 8. Selecting AUX Input 6 9. Selecting Factory Satellite (if equipped) 7 10. Troubleshooting 7 11. Warranty Information 8 Media Gateway & Optional Add-ons Media Gateway Harness Part #: PGHGM3 Factory Radio Not Included iPod Not Included Media Gateway Part #: PXAMG 3Ft. HD Radio Cable 11Ft. iPod Cable HD RadioTM Tuner (sold separately) Part #: HDRT Antenna Adapter * Required for most vehicles. (sold seperately) Media Gateway Harness Part #: PGHGM3 Factory Radio Not Included iPod Not Included Media Gateway Part #: PXAMG 3Ft. HD Radio Cable 11Ft. iPod Cable HD RadioTM Tuner (sold separately) Part #: HDRT Antenna Adapter * Required for most vehicles. (sold seperately) 1. Introduction Thank you for purchasing the Peripheral Electronics® Media Gateway. The Media Gateway is designed to provide endless hours of listening pleasure from your factory radio. To ensure that your iPod performs correctly with your radio, we recommend that you read this entire manual before attempting installation of the Media Gateway. The Media Gateway allows connectivity for iPod and the HD Radio tuner (HDRT sold separately), enabling full control of these devices from the factory installed radio. It also retains original system features such as Satellite Radio(if equipped). 2. Precautions UPDATING iPod FIRMWARE For proper operation of the Media Gateway, your iPod must be updated with the most recent version of firmware from Apple. This is done on your computer. To update the software on the iPod go to: Follow the directions on the website to complete the download. There is no charge for this update. PREVENTING DAMAGE TO YOUR VEHICLE OR iPod. Some installations require you to make wiring connections. To eliminate the risk of an electrical short, we recommend disconnecting the vehicle’s battery prior to installation. If you do not feel comfortable making these connections, we suggest you seek professional installation. We recommend that the iPod be disconnected from the interface when the vehicle is not in use. PROPER MOUNTING LOCATION Securely install the interface in a location free from; heat, humidity, moving parts, sharp metal edges or direct sunlight. We recommend securing the interface to a suitable location using; double sided tape, VelcroTM or zip-ties. 3. Compatibility Please visit to verify your vehicle’s compatibility. 4. Dipswitch Settings All 4 dipswitches MUST be set in the OFF (up) position for proper operation. (See fig.1 on next page) 2 Fig. 1 Side view of interface with dip switches in correct position OFF ON 5. Installation 1. When making electrical connections we always recommended disconnecting the vehicle’s battery from the electrical system before performing the installation. 2. Carefully remove the trim panels covering the 7mm bolts that secure the radio into the dash cavity. Remove these bolts, and carefully pull the radio from the dash of the vehicle. This will provide access to the factory radio connectors where you will connect the Media Gateway harness. 3. Disconnect the factory 24-Pin harness and 12-Pin harness from the back of the radio (if present). Disconnect the antenna from the radio. 4. Connect the 8-Pin iPod docking cable into the first port on the Media Gateway (farthest away from dipswitches). Carefully run the 11 foot iPod cable behind the dash to the location where the iPod will be mounted or stored (for example the glove box or center console). This location will vary based on the vehicle, and the customer’s prefrence. When running this cable through the dash be sure to secure it away from moving parts or sharp metal edges that may damage the cable. 5. If connecting the HD Radio Tuner (HDRT sold separately), make the following connections before connecting the PXAMG to the vehicle. Plug the 3 foot HD Radio Cable (8-Pin mini-din to 8-Pin mini-din) into the second port (closest to the dipswitches) on the Media Gateway. Connect the other end of this cable into the HD Radio tuner. Connect the factory antenna cable into the antenna connection on the HD Radio tuner (HDRT) Using a BestKits BAA5 antenna adaptor or eqivilalent if needed to make this connection. 6. Locate the 24-pin and 12-pin male connectors on the PGHGM3 harness, plug these connectors into the back of the radio. Plug the Black micro-fit 24-pin connector on the PGHGM3 harness into the PXAMG Media Gateway box. 2 Fig. 1 Side view of interface with dip switches in correct position OFF ON 5. Installation 1. When making electrical connections we always recommended disconnecting the vehicle’s battery from the electrical system before performing the inst...