Оценок - 4, средний балл: 4.5 ( )

Производитель: Beko Размер: 745 kb Название файла: Язык инструкции:

Take out all trays and the grill out of the oven. Clean out the interior with a piece of moist, soapy cloth. Then, clean it once more with a wet piece of cloth and let it to dry. Do not use dry powder agents far cleaning. Special cleaners that are commercially available may be used after carefully reading the warning that are written on the labels. * Catalytic-enamelled models; The oven inlerior of this model Is coated with catalytic enamel since the catalytic enamel cleans itsellf, you do not have to perform an extra cleaning after the cooking operation. If your oven obtains steel rack; To clean the steel rack, unscrew the 4 screws. After cleaning operation, assemble the steel rack to the oven body again. Steel wool I Cleaning powders abrasive sponges Do not use these materials for cleaning Lowering the heating element Warning! Make sure that the heating element is sufficiently cool before you start cleaning. Warning! Never switch on the heating element or place any wright on it when the heating element is in the lowered position. 1. Unlock the heating elementby turning the screw at the seiling of the oven cavity. 2. After cleaning, move the heating element upward and screw it to the ceiling of the oven cavity. Replacing the oven lamp: 1. Unplug the power cable. 2. Then, remove theprotective glass cover of the lamp inside your oven by turning it counterclockwise. 3. Then, remove the bulb by turning it counter-clockwise. 4. After installing the correct bulb obtained from an Authorized Service, reinstall the protective glass of the lamp. For the square-shaped lamp models: There are 2 square-shaped lamps at right and left side of the oven inside. Both lamps are on and off at the same time. Replacing the Oven Lamp Disconnect the appliance from the supply Take out screws on the side shelve. Take out Lens of the oven lamp by means of the flat screwdriwer. Replace defective lamp with the new one. Reinstall lens and side shelf. Lamp type is 220-230V, 1 5/25W E14,T300°C 21 Oven-Mounting and Warnings Things to Pay Special Attention to Regarding the Electrical Connection - Have the device's electricity connected by a certified electrician. - This device belongs to the primary protection class and must be operated only via a grounded electrical connection. - The device must be installed in such a way as to prevent contact with the electrical connections. - If, together with the product, a main cord is not provided, or if a main cord is provided without a plug: a circuit breaker must be used with the product such that a 3 mm gap stands between all contacts capable of severing the electricity among all of the poles on the product. - During product installation, ensure that no more than one of its side surfaces, if necessary, stands close to a high wall or cupboard. In wall ovens that come with the pyrolitic cleaning function, a minimum distance of 30 mm must be left between the oven's front panel and furniture or wall of the building. - For the safe and reliable operation of the device, it is recommended that the back wall of the compartment into which it is installed be open. - The consituent materials of the installation cavity must be able to withstand a temperature of 100°C. This is especially applicable to and important for wooden materials, coverings that adhere to edges, plastic surfaces, applied adhesives, paints and polishes. Furniture in the device's immediate vicinity must be able to with stand a temperature of at least 70°C. Matters to Pay Special Attention to Regarding the Oven's Installation Cavity! Prior to installing the device, the cutting of furniture and countertops or renovation activities need to have been completed. Sawdust and debris on the surfaces of furniture near which the product is to be installed must be cleaned. Otherwise the device's cord and electrical connection could become damaged. - For the furniture cavity dimensions and the placement of the 2 device, see the diagram. - If a drawer is to be located underneath the device, a separator panel must be placed between the device and the drawer. - Because the device is installed flush with the back wall, the electrical socket, except for the device's mounting area, must be located in an easily accessible place. - For integrated ovens, the electrical connections and installation of the stove control buttons must take into account that the stove control buttons will be on the front panel of the oven. - Ensure that the furniture cabinet of the kitchen countertop has been stabilized/immobilized. - For the oven's proper ventilation, there must be a distance of up to 35 mm between intervening furniture surfaces and the back wall. Matters to Pay Special Attention to Regarding the Positioning of the Oven - By pushing the device, insert it fully into the furniture compartment. Attention! During insertion, ensure that the electrical cable is not broken or pinched. - For air circulation, some empty...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: