Оценок - 1, средний балл: 4 ( )

Производитель: CDA Размер: 2.87 mb Название файла: Язык инструкции:

16); – Replace the halogen lamp B with a new one suitable for high temperatures having the following specifications: 230V and same power (check watt power as stamped in the lamp itself) of the replaced lamp. IMPORTANT WARNING: Never replace the bulb with bare hands; contamination from your fingers can cause premature failure. Always use a clean cloth or gloves. – Refit the protective cover; Left Lamp (Model "6Q5.." Only): – Remove the left wire rack by unscrewing the fixing screws. – Press down from the top the protective cover A (fig. 16) and remove it by rotating on the lower side. IMPORTANT: never use screwdrivers or other utensils to remove the cover A. This could damage the enamel of the oven or the lampholder. Operate only by hands. – Replace the halogen lamp B with a new one suitable for high temperatures having the following specifications: 230V and same power (check watt power as stamped in the lamp itself) of the replaced lamp. IMPORTANT WARNING: Never replace the bulb with bare hands; contamination from your fingers can cause premature failure. Always use a clean cloth or gloves. – Refit the protective cover A operating in reverse order. ATTENTION: the notch in the inner edge of the cover must be oriented toward the lamp. – Assemble the left wire rack. Note: Oven bulb replacement is not covered by your guarantee. Models: SV100.. SV150.. 6Q5.. Model: 6Q5.. ABBC12AAFig. 16 WRONG CORRECT 28 28 Assembling and Dismantling of the Side Runner Frames – Assemble the wire racks to the oven walls using the 2 screws (Fig. 17). – Slide the tray and rack into the runners (Fig. 18). The rack must be fitted so that the safety catch, which stops it sliding out, faces the inside of the oven. – To dismantle, operate in reverse order. ALL Models Fig. 18 Fig. 17 29 Drop-down Grill Element – To lower the grill element: use a flat-head screwdriver or a small coin to loosen the element fixing screw. – When you have finished cleaning the oven ceiling, raise the grill element and screw the element fixing screw back onto the stud. – Make sure that the fixing screw is tightened and the element is held securely in place. The grill element itself is self-cleaning. Fixing screw Stud Fig. 19 Fig. 20 Model: 6Q5.. 30 30 Telescopic Sliding Shelf Supports The telescopic sliding shelf supports make it safer and easier to insert and remove the oven shelves and trays. They stop when they are pulled out to the maximum position. Important! When fitting the sliding shelf supports, make sure that you fit: – The slides to the top wire of a rack. They do not fit on the lower wire. – The slides so that they run out towards the oven door. – Both sides of each pair of shelf slides. – Both sides on the same level. To fix the sliding shelf support onto the side racks: – Screw the side rack onto the oven wall (Fig. 21). – Fit the sliding shelf support onto the top wire of a rack and press (Fig. 21). You will hear a click as the safety locks clip over the wire. Left Right Fig. 21 Model: 6Q5.. 31 31 To remove the telescopic sliding shelf supports: – Remove the side racks by unscrewing the fixing screws (Fig. 22). – Lay down the telescopic sliding shelf support and side racks, with the telescopic sliding shelf support underneath. – Find the safety locks. These are the tabs that clip over the wire of the side rack (arrow 1 in Fig. 23). – Pull the safety locks away from the wire to release the wire (arrow 2 in Fig. 23). Cleaning the Sliding Shelf Supports – Wipe the supports with a damp cloth and a mild detergent only. – Do not wash in the dishwasher, immerse in soapy water, or use oven cleaner. 121Fig. 22 Fig. 23 32 32 Oven Door All models Removing the Oven Door The oven door can easily be removed as follows: – Open the door to the full extent (fig. 24a). – Open the lever A completely on the left and right hinges (fig. 24b). – Hold the door as shown in fig. 24. – Gently close the door (fig. 24c) until left and right hinge levers A are hooked to part B of the door (fig. 24b). – Withdraw the hinge hooks from their location following arrow C (fig. 24d). – Rest the door on a soft surface. – To replace the door, repeat the above steps in reverse order. Fig. 24 Fig. 24a AA BB Fig. 24b Fig. 24c CC Fig. 24d 33 33 Oven Door - Removable Inner Pane of Glass All models except: Cleaning the Panes of Glass 6Q5.. The oven door is fitted with no. 2 panes: - no. 1 outside; - no. 1 inner; To clean the panes on both sides it is necessary to remove the inner pane as follows. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they scratch the surface, which may result in shattering of the glass. Removing the Inner Pane of Glass The oven door has two panes. To clean these, you need to remove the inner pane. 1. Lock the door open: – Fully open the oven door (fig. 25). – Fully open the lever A on the left and right hinges (Fig 26). – Gently close the door (Fig. 27) until the left and right hinges are hooked to part B of the door (F...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: