Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Avoid touching exposed blades on underside of confetti-cut shredder head. • Plug power cord in an outlet that can easily be reached. • Do not place shredder near or over a heat or water source. While operating shredder • Keep hands and hanging objects (jewelry, ties, loose clothing, long hair, etc.) away from paper entry • Keep children and pets away from shredder. 5.450" DiaP500-25.450" When not in use • Always turn off and unplug shredder • Unplug before emptying basket • Do not open shredder head: Danger of electric shock NOTE: Do not use flammable synthetic oil, petroleum-based products or aerosols of any kind on or near product at any time. Set-Up CONFETTI-CUT (T440C): • Recommendation: Place plastic waste bag (Fellowes part number 36052) into basket to collect confetti particles. • For safety reasons, this model will operate only if the shredder head is in the correct position on the basket. Align slot at the back of the shredder head (A) with tab on the back of the basket (B) and place it onto the basket in this position. Operation For convenience, your shredder is equipped with an automatic-start sensor (C). This means that when the control switch (D) is in the automatic (I) position, the shredder will start running when you put paper into it and stop 1 or 2 seconds after the paper has passed through. Because the sensor cannot tell the difference between paper and other objects, this feature can also be a hazard, especially to children and pets. To avoid accidents, turn off the shredder as soon as you are finished. Unplug shredder if it will not be used for an extended period. To shred: • Plug in shredder with control switch (D) in off (O) position • Slide control switch to automatic (I) position to signal readiness Paper • Feed paper straight into entry (E), until the shredder automatically begins shredding; see Product Profile for limits on paper width, shreddable items, sheet capacity, etc. • Shred for no more than 5-7 minutes; shredding longer will cause shredder to turn itself off for 15 minutes to cool down. • Slide control switch to off (O) position after cutting has stopped; cutting continues for 1 or 2 seconds after paper has gone through in order to clear shredded paper from cutting cylinders. In case of a paper jam, which may occur if the shredder is pushed beyond its specified capabilities, press the control switch to the off (0) position and empty the basket if full. Then: 1) Slide control switch in reverse (R) position and attempt to back paper out of shredder. 2) If shredder jams in reverse mode, slide control switch to automatic (I) position and attempt to continue shredding operation. 3) If shredder jams again, alternate control switch slowly between reverse (R) and automatic (I) positions to attempt to move jammed paper completely through shredder. If you are unable to clear the jam using this method, turn off and unplug the shredder; remove shredder head from the wastebasket and carefully remove any paper extending below the cutting cylinders; empty the wastebasket; reassemble the shredder and repeat jam clearing procedure. Maintenance Regular emptying of the basket is important to ensure the smooth operation of the cutting cylinders. If paper is within 2 inches of shredder head, turn off and unplug the shredder, remove the shredder head and empty the basket. Regular oiling of the shredder is also necessary to ensure proper performance. If you are running the shredder at or near capacity, we recommend oiling it monthly. Using Fellowes Powershred Lubricant #35250 or other non-aerosol vegetable-based oil in a long-nozzle container: • Apply oil over full width of paper entry (E) with shredder in off [O] position. • Press control switch to automatic [I] position which will cause shredder to run for about 2 seconds. • Press and hold control switch in reverse [R] position for 3–5 seconds. • Repeat above automatic [I] and reverse [R] sequence three times. REMINDER: Do not use flammable synthetic oil, petroleum-based products or aerosol lubricants of any kind in or near the shredder at any time. Troubleshooting If you have a problem with your shredder, check the symptoms and remedies below. If you cannot solve the problem this way, contact Fellowes Customer Service. Do not open shredder head to attempt repair: It could expose you to serious electric shock and will void your warranty. SymptomRemedy Shredder does not start or stops • Make sure shredder is plugged in and while shredding switch is in automatic (I) position • If paper appears to be jammed, follow instructions under Operation • Check shredder head position; follow instructions under Set-Up to correct • Wait 4 minutes for shredder to cool down before trying again Shredder runs below capacity • Check to see if basket is full, follow instructions under Maintenance. • Oil cutting cylinders. Follow instructions under Maintenance. Shredder continues to run for 1 or 2 • No action required. This is a self- seconds after shredding has...